Snapper M280919B, M250819BE, M281019BE, M300919B, M301019BE Service After First 5 Hours

Page 12

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and vent must be closed securely to prevent fuel spillage.

3.1INTRODUCTION

To retain the quality of the Rear Engine Rider, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Rear Engine Riding Mower, always mention the model and serial number. SNAPPER recommends returning the Rear Engine Rider to an authorized SNAPPER dealer annually for inspection and addition of any new devices which might upgrade the safety of the Rear Engine Rider. For the nearest SNAPPER dealer in your area, check the yellow pages under the heading LAWN MOWERS. For engine parts and service, look for the engine manufacturer’s dealers under the heading, ENGINES - gasoline.

3.2SERVICE - AFTER FIRST 5 HOURS

Routine maintenance is important to the performance and life of your Rear Engine Rider. Service performed properly and at the recommended interval is essential.

Refer to Section “MAINTENANCE SCHEDULE” in this manual and in the Engine Owner’s Manual. Carefully complete all of the recommended service procedures.

3.2.1. CHANGE ENGINE OIL

1.Place bricks or wooden blocks under the front wheels to lower rear of engine.

2.Loosen or remove oil fill cap on engine.

3.Loosen oil drain plug.

4.Place a 2 quart minimum capacity container under the end of the oil drain. Open oil drain. See Figure 3.1 for oil drains used on the Rear Engine Riders.

REMOVE OIL

PLUG TO ALLOW

OIL TO DRAIN

FIGURE 3.1

5.After all the oil has drained, close the drain and wipe up any oil that may have spilled. See Figure 3.1. Dispose of used oil properly.

6.Fill engine crankcase with new oil. Refer to your engine owner’s manual for oil specifications.

3.2.2. SERVICE ENGINE AIR CLEANER

The engine is equipped with a dual element air cleaner. Both the foam pre-cleaner and cartridge require service. Refer to Engine Owner’s Manual for recommended service procedures.

3.2.3. CHECK MOWER BLADE

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

WARNING

Remove the battery if the Rear Engine Rider will be left standing on the rear bumper for longer than 2 hours. See Section on BATTERY REMOVAL. DO NOT use a cutting blade that shows signs of excessive wear or damage on the Rear Engine Rider. Refer to Section on MOWER BLADE REPLACEMENT for proper blade inspection and service procedures.

4.Check torque of blade mounting bolts. As necessary, torque to 30 to 40 ft. lbs. See Figure 3.2.

5.Check blade for sharpness, wear and damage. See Section on BLADE WEAR LIMITS.

TORQUE BLADE BOLTS TO 30 TO 40 FT. LBS.

FIGURE 3.2

6.Check blade for straightness. Refer to Section on ADJUSTING MOWER BLADE.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Rear Engine Riding Mower Series Manual No -1947 REV , 8/20/99Important Safety Instructions Operation Table of Contents Introduction NomenclatureOPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextStarting & Operation Engine Electric StartEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park the machine on slopes Service After First 5 Hours Service Engine AIR Cleaner Check Mower BladeChange Engine OIL Service After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock SystemService Every 25 Operating Hours Battery Fluid LevelLevelness Clean Mower Deck Lubrication Grease FittingsService Every 25 Operating Hours 3.3.8. Rear Axle Bearing Service Annually Fuel FilterEvery TWO Years Storage OUT of SeasonEngine Adjustments & Repair Mower Drive Belt Adjustment for 25, 28 & 30 M ModelsBlade Brake Adjustment Mower Deck Adjustment Front to Rear Levelness 25 & 28 DecksFront to Rear Levelness 30 Decks Wheel Brake Adjustment Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBlade Drive Belt Replacement Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationBattery Service Battery StorageNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Rear Engine Riding Mower Series

M280919B, M250819BE, M281019BE, M300919B, M301019BE, M300919B, M250819BE, M280919B, M281019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B, M301019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B specifications

The Snapper series, specifically the models M301019BE, M250819BE, M280919B, M281019BE, and M300919B, represents a robust lineup of powered lawn maintenance equipment designed for both residential and commercial use. Each model in this series offers a unique set of features, technologies, and characteristics that cater to diverse landscaping needs.

One of the standout features across the Snapper models is their powerful, reliable engines. Equipped with advanced engine technology, they deliver optimal performance, ensuring efficient cutting, mulching, and bagging capabilities. Users can expect smooth operation and the ability to tackle various types of grass and terrains without compromise. The ergonomic design of the handles allows for ease of use and reduces operator fatigue, ensuring a comfortable mowing experience.

The M301019BE model, for instance, boasts a cutting width that allows for expansive mowing in a single pass, making it suitable for larger yards. This model also features height-adjustable cutting decks, enabling users to customize their mowing height as per the season or grass type, providing versatility throughout the year.

In contrast, the M250819BE is more compact, making it ideal for smaller lawns or tight spaces. It may lack some of the high-end features of its larger counterparts, but its maneuverability and ease of storage make it a practical choice for homeowners with limited space.

The M280919B and M281019BE models further enhance the series by incorporating Snapper's innovative cutting technologies. These models are designed with precision cutting blades that ensure a clean, even finish on any lawn. The inclusion of mulching capabilities allows users to recycle grass clippings, promoting a healthier lawn while minimizing waste.

The M300919B offers an enhanced user experience with advanced features such as quick release grass bag systems, making the disposal of clippings easier than ever. This model also features durable wheels for improved traction and maneuverability across varied terrains.

Across the Snapper lineup, durability is a hallmark trait. Each unit is constructed with high-quality materials designed to withstand the rigors of outdoor use. This commitment to quality ensures that owners can rely on their equipment season after season.

In summary, the Snapper M301019BE, M250819BE, M280919B, M281019BE, and M300919B models represent a versatile and powerful choice for anyone looking to maintain their yard. With reliable engines, user-friendly designs, and innovative mowing technologies, these models offer excellent options for all types of mowing needs. Whether dealing with expansive lawns or smaller residential spaces, Snapper continues to deliver quality and performance in every cut.
Top Page Image Contents