Snapper M301019BE, M250819BE, M280919B, M281019BE, M300919B Blade Brake, Interlock System

Page 13

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and vent must be closed securely to prevent fuel spillage.

3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.4. CHECK BLADE DRIVE BELT

The blade drive consists of a single belt from the engine to the deck. Inspect for signs of deterioration and proper tension.

1.Lower deck to lowest setting.

2.Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3.

3.Slide cover back and rotate out.

REMOVE FOUR

SCREWS TO REMOVE

COVER

FIGURE 3.3

4.With engine “OFF” and deck in 3rd height of cut position, move blade lever back to the “ON” position and depress blade pedals.

5.Measure the belt spacing at idler pulley. See Figure 3.4. The belt spacing should be 1 1/4” but no less 1”. If the measurement is less than 1”, the belt tension should be adjusted. Refer to Section “MOWER DRIVE BELT ADJUSTMENT”.

ENGINE

PULLEY

BELT SPACING SHOULD BE 1-1/4”

IDLER

PULLEY

MOWER DECK

PULLEY

FIGURE 3.4

3.2.5.BLADE BRAKE

1.Check blade brake for proper function. Blade should stop rotating in 3 seconds or less after moving the blade control lever to the “OFF” position or after releasing the blade pedals.

WARNING

Blades must stop rotating in 3 seconds or less after the blade has been turned off. DO NOT operate machine until blade brake has been adjusted and functioning properly.

2.If the blade continues to rotate longer than 3 seconds do not operate machine. Refer to Section “BLADE BRAKE ADJUSTMENT” or contact your SNAPPER dealer for assistance.

3.2.6.SERVICE BRAKE / PARK BRAKE

1.Check machine brake for proper function. Engage park brake. Push machine. Rear tires should skid. Drive machine forward and apply brake. Machine should come to a complete stop in less than 5 ft.

2.If brakes are not functioning properly brake adjustment must be completed before operating machine. Refer to Section “SERVICE BRAKE – PARK BRAKE ADJUSTMENT”.

3.2.7.INTERLOCK SYSTEM

Check interlock controls for proper function:

The engine MUST NOT start if:

1.Blade Control is “ON” and/or clutch/brake pedal is released.

The engine and blades MUST STOP if:

2.The operator leaves the operator position with Blade Control “ON” and/or clutch/brake pedal is released.

WARNING

DO NOT operate machine if interlock system is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Manual No -1947 REV , 8/20/99 Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionPRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Electric Start Starting & OperationEngine Manual Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park the machine on slopes Service Engine AIR Cleaner Check Mower Blade Service After First 5 HoursChange Engine OIL Service Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Interlock SystemBattery Fluid Level Service Every 25 Operating HoursLevelness Clean Mower Deck Lubrication Grease FittingsService Every 25 Operating Hours 3.3.8. Rear Axle Bearing Fuel Filter Service AnnuallyEvery TWO Years Storage OUT of SeasonMower Drive Belt Adjustment for 25, 28 & 30 M Models Engine Adjustments & RepairBlade Brake Adjustment Front to Rear Levelness 25 & 28 Decks Mower Deck AdjustmentFront to Rear Levelness 30 Decks Wheel Brake Adjustment Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Replacement Blade Drive Belt ReplacementBelt Removal Battery Installation Battery Battery RemovalBattery Storage Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Rear Engine Riding Mower Series

M280919B, M250819BE, M281019BE, M300919B, M301019BE, M300919B, M250819BE, M280919B, M281019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B, M301019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B specifications

The Snapper series, specifically the models M301019BE, M250819BE, M280919B, M281019BE, and M300919B, represents a robust lineup of powered lawn maintenance equipment designed for both residential and commercial use. Each model in this series offers a unique set of features, technologies, and characteristics that cater to diverse landscaping needs.

One of the standout features across the Snapper models is their powerful, reliable engines. Equipped with advanced engine technology, they deliver optimal performance, ensuring efficient cutting, mulching, and bagging capabilities. Users can expect smooth operation and the ability to tackle various types of grass and terrains without compromise. The ergonomic design of the handles allows for ease of use and reduces operator fatigue, ensuring a comfortable mowing experience.

The M301019BE model, for instance, boasts a cutting width that allows for expansive mowing in a single pass, making it suitable for larger yards. This model also features height-adjustable cutting decks, enabling users to customize their mowing height as per the season or grass type, providing versatility throughout the year.

In contrast, the M250819BE is more compact, making it ideal for smaller lawns or tight spaces. It may lack some of the high-end features of its larger counterparts, but its maneuverability and ease of storage make it a practical choice for homeowners with limited space.

The M280919B and M281019BE models further enhance the series by incorporating Snapper's innovative cutting technologies. These models are designed with precision cutting blades that ensure a clean, even finish on any lawn. The inclusion of mulching capabilities allows users to recycle grass clippings, promoting a healthier lawn while minimizing waste.

The M300919B offers an enhanced user experience with advanced features such as quick release grass bag systems, making the disposal of clippings easier than ever. This model also features durable wheels for improved traction and maneuverability across varied terrains.

Across the Snapper lineup, durability is a hallmark trait. Each unit is constructed with high-quality materials designed to withstand the rigors of outdoor use. This commitment to quality ensures that owners can rely on their equipment season after season.

In summary, the Snapper M301019BE, M250819BE, M280919B, M281019BE, and M300919B models represent a versatile and powerful choice for anyone looking to maintain their yard. With reliable engines, user-friendly designs, and innovative mowing technologies, these models offer excellent options for all types of mowing needs. Whether dealing with expansive lawns or smaller residential spaces, Snapper continues to deliver quality and performance in every cut.
Top Page Image Contents