Snapper M300919B, M250819BE, M280919B, M281019BE, M301019BE Lubrication Grease Fittings

Page 14

Section 3 - MAINTENANCE

3.2.8.LUBRICATION – GREASE FITTINGS

The following components on the Rear Engine Rider are equipped with grease fittings and require periodic lubrication. Apply General Purpose grease (NLGI No.2) with a grease gun.

1.Front Wheel Bearings. Refer to Section

“FRONT WHEEL BEARINGS – LUBRICATION”.

2.Rear Axle Bearing. Refer to Section “REAR

AXLE BEARING – LUBRICATION”.

3.Mower Blade Spindle. Refer to Section

“MOWER BLADE SPINDLE – LUBRICATION”.

3.3 SERVICE - EVERY 25 OPERATING HOURS

3.3.1.Perform all service required after the first 5 hours of operation. Refer to Section “SERVICE – AFTER 5 HOURS”.

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3.2.BATTERY FLUID LEVEL

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Remove battery caps. Check fluid level.

3.Add water only to bring fluid to proper level – approximately 3/16” above plates.

DO NOT OVERFILL.

4.Reinstall battery. Refer to Section “BATTERY INSTALLATION”.

3.3.3.MOWER DECK LEVELNESS

Check mower deck for proper level. Adjust as required. Refer to Section “MOWER DECKADJUSTMENT –

LEVELNESS”.

3.3.4.CLEAN MOWER DECK

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

5.Clean top of deck, removing all grass clippings and debris.

3.3.5MOWER BLADE SPINDLE - LUBRICATION

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “FUEK TANK REMOVAL”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Lubricate spindle with three shots of general purpose grease from grease gun. See Figure 3.5.

IMPORTANT: If the Rear Engine Rider will be on its rear bumper for longer than two hours, remove the battery. Refer to Section “BATTERY REMOVAL”.

3.3.6.MOWER DECK LINKAGE - LUBRICATION Lubricate all mower deck linkage pivot points with a light coat of motor oil.

SPINDLE

GREASE

FITTING

FIGURE 3.5

3.3.7. FRONT WHEEL BEARING - LUBRICATION

1.Lubricate front wheel bearings with five shots of general purpose grease, from grease gun. See Figure 3.6.

FRONT WHEEL

GREASE FITTING

FIGURE 3.6

(Continued on Next Page)

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Rear Engine Riding Mower Series Manual No -1947 REV , 8/20/99Important Safety Instructions Operation Table of Contents Introduction NomenclatureOPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Manual Start Starting & OperationEngine Electric Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeDo not park the machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Change Engine OIL Service After First 5 HoursService Engine AIR Cleaner Check Mower Blade Blade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Interlock SystemLevelness Clean Mower Deck Service Every 25 Operating HoursBattery Fluid Level Lubrication Grease FittingsService Every 25 Operating Hours 3.3.8. Rear Axle Bearing Every TWO Years Service AnnuallyFuel Filter Storage OUT of SeasonEngine Adjustments & Repair Mower Drive Belt Adjustment for 25, 28 & 30 M ModelsBlade Brake Adjustment Front to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 25 & 28 Decks Wheel Brake Adjustment Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Removal Blade Drive Belt ReplacementBelt Replacement Battery Battery Removal Battery InstallationNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Rear Engine Riding Mower Series

M280919B, M250819BE, M281019BE, M300919B, M301019BE, M300919B, M250819BE, M280919B, M281019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B, M301019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B specifications

The Snapper series, specifically the models M301019BE, M250819BE, M280919B, M281019BE, and M300919B, represents a robust lineup of powered lawn maintenance equipment designed for both residential and commercial use. Each model in this series offers a unique set of features, technologies, and characteristics that cater to diverse landscaping needs.

One of the standout features across the Snapper models is their powerful, reliable engines. Equipped with advanced engine technology, they deliver optimal performance, ensuring efficient cutting, mulching, and bagging capabilities. Users can expect smooth operation and the ability to tackle various types of grass and terrains without compromise. The ergonomic design of the handles allows for ease of use and reduces operator fatigue, ensuring a comfortable mowing experience.

The M301019BE model, for instance, boasts a cutting width that allows for expansive mowing in a single pass, making it suitable for larger yards. This model also features height-adjustable cutting decks, enabling users to customize their mowing height as per the season or grass type, providing versatility throughout the year.

In contrast, the M250819BE is more compact, making it ideal for smaller lawns or tight spaces. It may lack some of the high-end features of its larger counterparts, but its maneuverability and ease of storage make it a practical choice for homeowners with limited space.

The M280919B and M281019BE models further enhance the series by incorporating Snapper's innovative cutting technologies. These models are designed with precision cutting blades that ensure a clean, even finish on any lawn. The inclusion of mulching capabilities allows users to recycle grass clippings, promoting a healthier lawn while minimizing waste.

The M300919B offers an enhanced user experience with advanced features such as quick release grass bag systems, making the disposal of clippings easier than ever. This model also features durable wheels for improved traction and maneuverability across varied terrains.

Across the Snapper lineup, durability is a hallmark trait. Each unit is constructed with high-quality materials designed to withstand the rigors of outdoor use. This commitment to quality ensures that owners can rely on their equipment season after season.

In summary, the Snapper M301019BE, M250819BE, M280919B, M281019BE, and M300919B models represent a versatile and powerful choice for anyone looking to maintain their yard. With reliable engines, user-friendly designs, and innovative mowing technologies, these models offer excellent options for all types of mowing needs. Whether dealing with expansive lawns or smaller residential spaces, Snapper continues to deliver quality and performance in every cut.
Top Page Image Contents