Snapper M280919B, M250819BE, M281019BE, M300919B, M301019BE Service Annually, Fuel Filter

Page 16

Section 3 - MAINTENANCE

3.4SERVICE - ANNUALLY

3.4.1.Perform all maintenance as specified in “MAINTENANCE SCHEDULE” Section of this manual.

3.4.2.FUEL FILTER

Service fuel filter as instructed below, on COLD ENGINE ONLY!

IMPORTANT: To stop flow of fuel, tank may be removed from bracket and set on the floor so the fuel level will be below the filter. Refer to Section “REMOVING FUEL TANK”.

1.Remove hose clamps from fuel filter.

2.Remove fuel lines from filter. Discard filter.

3.Install new fuel filter. See Figure 3.10.

4.Reinstall fuel tank into bracket.

HOSE

CLAMPS

FUEL

FILTER

P.N. 1-4359

FIGURE 3.10

3.5EVERY TWO YEARS

In addition to regular maintenance, the following components of the Rear Engine Rider should be carefully inspected every two years for wear or damage. Replace worn or damaged parts with genuine SNAPPER replacement parts available from an authorized SNAPPER dealer.

3.5.1.All bushings and pivot areas.

3.5.2.Check both front wheel king pins.

3.5.3.Transmission shift lever and detent.

3.5.4.Clutch disc.

3.5.5.Clutch Yoke (See Figure 4.9).

3.5.6.Mower deck linkage and pivot areas.

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.6STORAGE (OUT OF SEASON)

If desired, the Rear Engine Rider can be stored on the rear bumper. Perform the following procedures to insure the Rear Engine Rider will operate properly when taken out of storage.

3.6.1.Thoroughly clean the Rear Engine Rider by removing all grass clippings and debris.

3.6.2.Perform maintenance and lubrication as required.

3.6.3.Drain fuel from fuel tank.

3.6.4.Start engine and allow it to run until engine runs out of fuel. This allows the carburetor and fuel system to remain clean during storage.

3.6.5.Remove battery. Refer to Section

“BATTERY STORAGE”.

3.6.6.Close vent on fuel filler cap.

3.6.7.Carefully stand Rear Engine Rider on rear bumper in desired location for storage.

3.7REMOVING FUEL TANK

Before removing fuel tank from rear engine rider, move rider outdoors where fumes can be easily dissipated. Removal of the tank is accomplished from the left side of the machine by pulling the tank straight up and away from the fuel tank bracket. See Figure 3.11. Holding the fuel tank, remove the fuel filler cap and pour remaining fuel in an approved container.

FUEL

FILLER

CAP

FUEL TANK

FUEL

TANK

BRACKET

FIGURE 3.11

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Rear Engine Riding Mower Series Manual No -1947 REV , 8/20/99Important Safety Instructions Operation Table of Contents Introduction NomenclatureOPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Electric Start Starting & OperationEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park the machine on slopes Service Engine AIR Cleaner Check Mower Blade Service After First 5 HoursChange Engine OIL Service After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock SystemService Every 25 Operating Hours Battery Fluid LevelLevelness Clean Mower Deck Lubrication Grease FittingsService Every 25 Operating Hours 3.3.8. Rear Axle Bearing Service Annually Fuel FilterEvery TWO Years Storage OUT of SeasonEngine Adjustments & Repair Mower Drive Belt Adjustment for 25, 28 & 30 M ModelsBlade Brake Adjustment Front to Rear Levelness 25 & 28 Decks Mower Deck AdjustmentFront to Rear Levelness 30 Decks Wheel Brake Adjustment Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Replacement Blade Drive Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationBattery Service Battery StorageNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Rear Engine Riding Mower Series

M280919B, M250819BE, M281019BE, M300919B, M301019BE, M300919B, M250819BE, M280919B, M281019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B, M301019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B specifications

The Snapper series, specifically the models M301019BE, M250819BE, M280919B, M281019BE, and M300919B, represents a robust lineup of powered lawn maintenance equipment designed for both residential and commercial use. Each model in this series offers a unique set of features, technologies, and characteristics that cater to diverse landscaping needs.

One of the standout features across the Snapper models is their powerful, reliable engines. Equipped with advanced engine technology, they deliver optimal performance, ensuring efficient cutting, mulching, and bagging capabilities. Users can expect smooth operation and the ability to tackle various types of grass and terrains without compromise. The ergonomic design of the handles allows for ease of use and reduces operator fatigue, ensuring a comfortable mowing experience.

The M301019BE model, for instance, boasts a cutting width that allows for expansive mowing in a single pass, making it suitable for larger yards. This model also features height-adjustable cutting decks, enabling users to customize their mowing height as per the season or grass type, providing versatility throughout the year.

In contrast, the M250819BE is more compact, making it ideal for smaller lawns or tight spaces. It may lack some of the high-end features of its larger counterparts, but its maneuverability and ease of storage make it a practical choice for homeowners with limited space.

The M280919B and M281019BE models further enhance the series by incorporating Snapper's innovative cutting technologies. These models are designed with precision cutting blades that ensure a clean, even finish on any lawn. The inclusion of mulching capabilities allows users to recycle grass clippings, promoting a healthier lawn while minimizing waste.

The M300919B offers an enhanced user experience with advanced features such as quick release grass bag systems, making the disposal of clippings easier than ever. This model also features durable wheels for improved traction and maneuverability across varied terrains.

Across the Snapper lineup, durability is a hallmark trait. Each unit is constructed with high-quality materials designed to withstand the rigors of outdoor use. This commitment to quality ensures that owners can rely on their equipment season after season.

In summary, the Snapper M301019BE, M250819BE, M280919B, M281019BE, and M300919B models represent a versatile and powerful choice for anyone looking to maintain their yard. With reliable engines, user-friendly designs, and innovative mowing technologies, these models offer excellent options for all types of mowing needs. Whether dealing with expansive lawns or smaller residential spaces, Snapper continues to deliver quality and performance in every cut.
Top Page Image Contents