Snapper M301019BE, M250819BE, M280919B, M281019BE, M300919B Engine Adjustments & Repair

Page 17

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

4.1ENGINE ADJUSTMENTS & REPAIR

Refer to the engine owner’s manual for those adjustments and/or repairs that can be made by the owner.

4.2MOWER DECK & COMPONENT ADJUSTMENTS The following mower deck and component adjustments and repairs can be made by the owner. However, if there is difficulty in achieving these adjustments and repairs, it is recommended that these repairs be made by an authorized SNAPPER dealer.

WARNING

Once blade is disengaged it should come to a stop in 3 seconds or less. If the blade continues to rotate after 3 seconds the blade brake must be adjusted. DO NOT continue to operate the machine if the blade brake is not operating properly.

4.2.1.MOWER DRIVE BELT ADJUSTMENT (FOR 25”, 28" & 30" "M" MODELS)

1.Remove mower drive belt cover. Refer to Section “CHECK BLADE DRIVE BELT”.

2.Move blade lever up and over to the “ON” position.

3.Place deck cutting height in the 3rd position. Measure the belt spacing at idler pulley. The distance should measure 1-1/4” but no less than 1”. See Figure 4.1.

1-1/4”

 

IDLER

ENGINE DRIVE

SPINDLE

PULLEY

PULLEY

ASSEMBLY

PULLEY

 

 

4.If the distance is less than 1”, adjust belt tension.

5.Remove hairpin and flat washers from pivot stud. See Figure 4.2.

6.Pull front frame forward until distance between belt, with blade lever “ON”, measures 1-1/4”.

FLAT

WASHERS

HAIRPIN

FRAME

SPACERS

FIGURE 4.2

7.Install required number of snap-in frame spacers behind channel pivot until the 1-1/4” distance between belt is maintained. See Figure 4.3.

SNAP-IN FRAME

SPACER

P.N. 2-8395

FIGURE 4.3

8.Reinstall the required amount of flat washers removed in step “5.” and install hairpin. See Figure

4.2.Retain any remaining spacers for readjustment when a new belt is installed.

IMPORTANT: The SNAPPER "M" Series Rear Engine Rider Models are shipped with additional spacers specifically designed for the Rear Engine Rider. Should additional spacers be required, contact an authorized SNAPPER dealer.

FIGURE 4.1

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Manual No -1947 REV , 8/20/99 Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionPRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Manual Start Starting & OperationEngine Electric Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineDo not park the machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Change Engine OIL Service After First 5 HoursService Engine AIR Cleaner Check Mower Blade Service Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Interlock SystemBattery Fluid Level Service Every 25 Operating HoursLevelness Clean Mower Deck Lubrication Grease FittingsService Every 25 Operating Hours 3.3.8. Rear Axle Bearing Fuel Filter Service AnnuallyEvery TWO Years Storage OUT of SeasonMower Drive Belt Adjustment for 25, 28 & 30 M Models Engine Adjustments & RepairBlade Brake Adjustment Front to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 25 & 28 Decks Wheel Brake Adjustment Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Removal Blade Drive Belt ReplacementBelt Replacement Battery Installation Battery Battery RemovalBattery Storage Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Rear Engine Riding Mower Series

M280919B, M250819BE, M281019BE, M300919B, M301019BE, M300919B, M250819BE, M280919B, M281019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B, M301019BE, M301019BE, M250819BE, M280919B, M281019BE, M300919B specifications

The Snapper series, specifically the models M301019BE, M250819BE, M280919B, M281019BE, and M300919B, represents a robust lineup of powered lawn maintenance equipment designed for both residential and commercial use. Each model in this series offers a unique set of features, technologies, and characteristics that cater to diverse landscaping needs.

One of the standout features across the Snapper models is their powerful, reliable engines. Equipped with advanced engine technology, they deliver optimal performance, ensuring efficient cutting, mulching, and bagging capabilities. Users can expect smooth operation and the ability to tackle various types of grass and terrains without compromise. The ergonomic design of the handles allows for ease of use and reduces operator fatigue, ensuring a comfortable mowing experience.

The M301019BE model, for instance, boasts a cutting width that allows for expansive mowing in a single pass, making it suitable for larger yards. This model also features height-adjustable cutting decks, enabling users to customize their mowing height as per the season or grass type, providing versatility throughout the year.

In contrast, the M250819BE is more compact, making it ideal for smaller lawns or tight spaces. It may lack some of the high-end features of its larger counterparts, but its maneuverability and ease of storage make it a practical choice for homeowners with limited space.

The M280919B and M281019BE models further enhance the series by incorporating Snapper's innovative cutting technologies. These models are designed with precision cutting blades that ensure a clean, even finish on any lawn. The inclusion of mulching capabilities allows users to recycle grass clippings, promoting a healthier lawn while minimizing waste.

The M300919B offers an enhanced user experience with advanced features such as quick release grass bag systems, making the disposal of clippings easier than ever. This model also features durable wheels for improved traction and maneuverability across varied terrains.

Across the Snapper lineup, durability is a hallmark trait. Each unit is constructed with high-quality materials designed to withstand the rigors of outdoor use. This commitment to quality ensures that owners can rely on their equipment season after season.

In summary, the Snapper M301019BE, M250819BE, M280919B, M281019BE, and M300919B models represent a versatile and powerful choice for anyone looking to maintain their yard. With reliable engines, user-friendly designs, and innovative mowing technologies, these models offer excellent options for all types of mowing needs. Whether dealing with expansive lawns or smaller residential spaces, Snapper continues to deliver quality and performance in every cut.
Top Page Image Contents