Sherwood RX-770 manual Operations, Listening to a Program Source

Page 10

Operations

LISTENING TO A PROGRAM SOURCE

Turn the power on.

1

STANDBY

 

 

POWER ON

 

 

STANDBY

 

 

POWER ON

 

 

STNADBY

 

 

SPEAKER

DIMMER

SLEEP

 

or

A

B

 

 

 

CD

TAPE

AUX

PHONO

 

 

 

 

REPEAT

TUNER

 

 

 

 

A/B

 

 

 

 

 

CD

INTRO

ON/STANDBY

 

A

 

 

 

 

DECK SEL.

 

TAPE

 

 

 

B

 

 

 

 

 

TREBLE

+

BASS

 

 

 

 

 

+

 

 

T/P

 

MUTE

 

 

 

 

VOL.

 

Then this unit is turned on to enter the operating mode.

In the operating mode, when the POWER button on the front panel or the STANDBY button on the remote control is pressed, the unit is turned off to enter the standby mode.

In the standby mode, the STANDBY indicator lights up. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the memorized contents and operation readiness.

Switch the desired speakers on.

 

 

Select the desired input source.

 

2

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

FM/AM

CD

 

TAPE

 

AUX

PHONO

 

 

POWER ON

 

 

STANDBY

 

 

 

 

 

 

 

 

 

 

SPEAKER

 

 

 

 

 

 

 

 

 

 

 

A SPEAKER B

A

B

 

 

 

CD TAPE AUX

 

 

 

 

 

 

 

 

 

DIMMER

SLEEP

PHONO

POWER ON

 

STANDBY

 

 

 

 

SPEAKER

 

 

 

 

 

A

B

 

 

 

 

 

 

 

 

 

 

 

 

CD

TAPE

AUX

PHONO

 

 

SPEAKER

DIMMER

SLEEP

or

 

or

 

 

 

 

 

 

TUNER

A

B

 

 

 

 

 

 

 

TUNER

 

CD

TAPE

AUX

 

 

 

 

 

 

 

 

PHONO

 

 

 

 

 

 

REPEAT

 

 

 

 

 

 

 

 

 

 

 

 

 

A/B

 

 

 

 

 

REPEAT

TUNER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A/B

 

 

 

 

 

 

CD

 

INTRO

 

 

 

 

CD

INTRO

 

 

 

 

 

 

 

 

 

 

 

 

 

Then the corresponding speaker indication(“SPK

 

 

 

 

 

 

 

 

A(or/and) B” is displayed and the sound can be heard

Each time the FM/AM button on the front panel or

from the speakers connected to the selected speaker

the TUNER button on the remote control is pressed,

terminals.

 

 

 

 

 

the band is changed to AM or FM.

 

 

When using the headphones for private listening, press

 

 

 

 

 

 

 

 

the corresponding SPEAKER button to switch off both

 

 

 

 

 

 

 

 

A and B speakers.

 

 

 

 

 

 

 

 

 

 

 

 

 

Operate the selected component for

Adjust the volume to a comfortable

 

4 playback.

 

 

 

 

 

5 listening level.

 

B

 

 

 

 

 

 

 

 

 

 

VOLUME

 

 

TREBLE +

 

BASS

 

 

 

 

 

 

 

 

 

 

 

 

 

+

VOL.

 

 

 

 

 

 

 

 

 

 

T/P

 

MUTE

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

TUNE

MEMO TUNE

 

 

 

 

 

 

 

 

 

 

 

 

VOL.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+

 

 

 

 

 

 

 

 

 

 

FM MODE

VOL.

P.SCAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DOWN

UP

 

 

 

 

 

VOL.

 

 

 

 

 

 

 

 

 

 

 

 

 

1 0

Image 10
Contents Page Introduction Read this Before Operating Your UnitSafety Instructions Contents System Connections Digi Link Front Panel & Remote Controls Digi Link III System Remote ControlsTUNING/PRESET Mode Button Power ButtonStandby Indicator Speaker A, B Selector Buttons TUNING/PRESET UP/DOWN ButtonsRemote Sensor Tape Deck SectionFluorescent Display Operations Listening to a Program SourceAdjusting the sound volume balance Auto tuning Listening to Radio BroadcastsTuning to preset stations Memory Backup FunctionRecording Other FunctionsTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section