Pride Mobility Quantum 600 2HD, Quantum 640 4SP manual Seat Installation, To install the seat

Page 23

I V . A S S E M B L Y

Seat Installation

It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Uni- versal Mounting System (UMS). The UMS consists of universal parts that may be attached to the seat, regard- less of seat width or seat depth. The two main compo- nents are aluminum extrusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 11.

NOTE: If your power chair is equipped with a Spe- cialty Seat, Synergy Seat, or a TRU-Balance Power Positioning System, refer to the information provided in separate manuals.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so.

SEAT LATCH SAFETY

FRONT EXTRUSION

REAR EXTRUSION

TRAPEZE BARS

To install the seat:

1.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 11.

2.Lower the front extrusion onto the power seat base or front trapeze bar until the seat locks into place.

3.Flip the seat latch safety down.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

4.Install the controller into the mounting block or under the armrest. See figure 18 or 19. Tighten the setscrew(s).

5.Route the controller harness so that it cannot be pinched in the seat hinge.

MANDATORY! Prevent controller harness damage! Avoid routing the controller har- ness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie-down points for the controller harness to prevent the harness from get- ting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.

6.Gently push down and pull backward at the harness access point on the rear shroud until it releases. See figure 12.

7.Remove the rear shroud.

8.Plug the controller connector(s) into the power base. See figure 7.

9.Reinstall the rear shroud by aligning the side and back tabs with the holes in the main shroud. Gently push down and forward until all four tabs lock into place.

10.Secure the controller harness to the armrest receiver with one or more wire ties. See figure 13.

Figure 11. Universal Mounting System (Shown Without Armrests for Clarity)

HARNESS

ACCESS POINT

Figure 12. Rear Shroud Assembly

WIRE TIES

Figure 13. Controller Harness Routing on a Contour Seat

Quantum 600 Series

www.pridemobility.com

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Quantum Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Modifications Pre-Ride Safety CheckGeneral Guidelines Incline Information Weight LimitationsTire Inflation Cornering Information Freewheel ModeBraking Information Stationary Obstacles Steps, Curbs, etc Inclement Weather PrecautionsPublic Streets and Roadways Outdoor Driving Surfaces Lift/Elevation Products Stairs and EscalatorsDoors ElevatorsRemovable Parts Preventing Unintended Movement Motor Vehicle TransportPositioning Belts Transfers BatteriesReaching and Bending Electromagnetic and Radio Frequency Interference EMI/RFI Prescription Drugs/Physical LimitationsAlcohol/Smoking S a F E T Y I . Y O U R P O W E R C H a I R Quantum 600 Series Power ChairElectrical Components Quantum 600 Series Power Base Electrical Components To operate the manual freewheel levers Manual Freewheel LeversA S S E M B L Y Initial AssemblyTo install the seat Seat InstallationTransit Securement System Brackets Transit Securement System OptionalO M F O R T a D J U S T M E N T S Comfort AdjustmentsYou may need the following to make comfort adjustments Seat Height and Seat Angle AdjustmentTo change the position Seat Position AdjustmentManual Recline Seatback Adjustment To adjust the seatback angleArmrest Height Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Armrest Angle AdjustmentTo change the controller position Controller PositionTo extend the controller Foot Platform Angle Adjustment Foot Platform Height AdjustmentFoot Platform Depth Adjustment To release the positioning belt To install the positioning beltTo adjust the positioning belt for operator comfort Positioning BeltCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Frequently Asked Questions FAQs Battery Break-inHow can I get maximum range or distance per charge? Why do my new batteries seem weak?„ Daily Use „ Infrequent UseWhat about shipping? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesStorage Disposal of Your Power ChairCleaning and Disinfection Wheel ReplacementYou may need the following to change your batteries Battery ReplacementBattery Installation To replace the batteries When to See Your Quantum Rehab Provider for ServiceCorrective Maintenance Specifications P E N D I X I Specification SQuantum 600 Series Dimensions and Ground Clearance Page Product Serial # Quality Control Quantum 600 Series
Top Page Image Contents