|
|
|
| INSTRUCTIONS FOR: |
|
|
|
| S U P E R S T A R T |
|
|
|
| STARTER/CHARGERS |
MODELS: |
| SUPERSTART 220.V2 |
| SUPERSTART 310.V2 |
|
| |||
SUPERSTART |
| 320/1.V2 SUPERSTART 410.V2 |
| SUPERSTART 420/1.V3 |
|
|
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will give you years of trouble free performance if these instructions are carefully followed and the product is correctly maintained.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1.1. IMPORTANT: Small battery chargers are supplied with plugs fitted. Starter/chargers, however, can draw more than 13 amps from the mains supply when being used to crank large engines. For this reason starter/chargers are not supplied with a fitted plug. We recommend that for maximum performance your starter/charger is plugged into a 30 amp electrical supply, and further recommend that you consult an electrician in order to fit an appropriate plug.
The following statements on electrical safety must also be read and understood before using the starter/charger. 1.2. ELECTRICAL SAFETY. F WARNING! It is the userís responsibility to check the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board.
We recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified person, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. DO ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.2.1. above and use a Portable Appliance Tester (PAT).
1.2.4. DO ensure that cables are always protected against short circuit and overload.
1.2.5. DO regularly inspect power supply, leads, plugs for wear and damage and all electrical connections to ensure that none is loose. 1.2.6. DO check that the voltage marked on the product is the same as the electrical power supply
to be used and check that all fused plugs are fitted with the correct capacity fuse. 1.2.7. DO NOT pull or carry the powered appliance by its power supply lead and do not pull
plug by the cable. Products must not be pulled or carried by their output cables. 1.2.8. DO NOT use worn or damage leads, plugs or connections. Immediately replace
or repair by qualified persons.
1.2.9. We do not recommend the use of an extension cable with the charger as the power output may be seriously reduced.
1.2.10. Subject to 1.1. above, the following instruction is for fitting a 13 amp plug since this will be adequate for use when charging and when starting engines in small vehicles. No responsibility is accepted in the event that the product is misused and/or used with a 13 amp plug when a 30 amp supply is required.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ëEí. b) Connect the BROWN live wire to live terminal ëLí.
c) Connect the BLUE neutral wire to the neutral terminal ëNí.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the external insulation extends beyond the cable restraint and that the restraint is tight.
DANGER! BE AWARE,
1.3. PERSONAL PRECAUTIONS
! Ensure there is another person within hearing range of your voice, or close enough to come to your aid, should a problem arise when working near a
! Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery. ! Have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
! Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean running water for at least 15 minutes and seek immediate medical attention.
! Remove personal metallic items such as rings, bracelets, necklaces and watches. A
! Ensure hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine, remove ties and contain long hair. % DO NOT smoke or allow a spark or flame in the vicinity of battery or engine.
Superstart 220.V2, 310.V2, 320/1.V2, 410.V2, 420/1.V3 - 0051 - (1) 18/06/02