Creative WS-6615X Description, Specifications, Standard Accessories, Application, Noise BUILD-UP

CIRCULAR SAW SAFETY

■Kickback is a result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precau- tion as given below.

PREVENTION OF KICKBACK

■Maintain a firm grip with both hands on the saw and position you arms to resist kickback forces. Position your body to either side of the blade, but not in lime with the blade. Kickback could cause the saw to jump backwards, but kick- back forces can be controlled by the operator, if proper precautions are taken.

■When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICK- BACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

■When restarting a saw in the workpiece, center the saw blade in the kerf and check that teeth are not engaged into the material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.

■Support large panels to minimize the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

■Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing excessive friction blade bin- ding and kickback.

■Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.

■Use extra caution when making a "plunge cut" into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.

DESCRIPTION

1.	Spindle lock button	12.	Depth lock knob
2.	Hex-head bolt	13. Base plate
3.	Spanner	14.	Depth of cut
4.	Outer blade washer	15.	Depth scale
5.	Lower guard	16.	Bevel adjustment knob
6.	Lower guard lever	17.	Bevel scale
7.	Upper guard	18.	Trigger switch
8.	Blade	19. Safety button
9.	Inner blade washer	20.	Line guide
10.	Dust nozzle	21.	Depth adjustment lug
11.	Riving knife

SPECIFICATIONS

WS-6613 / WS-6615 / WS-6615X

Blade diameter	190 mm
(Use only blades of this diameter)
Blade bore diameter	30 mm
Max. thickness of blade disc	2.2 mm
Max. cutting capacities
at 0°	66 mm
at 45°	50 mm
Frequency	50 Hz
Voltage	110V, 230V AC
Input
WS-6613	1,300 W
WS-6615 / WS-6615X	1,500 W
No load speed
WS-6613	4,600/min
WS-6615 / WS-6615X	5,500/min
Net weight
WS-6613 / WS-6615X	5.1 kg
WS-6615	5.3 kg

STANDARD ACCESSORIES

Saw blade, Dust nozzle, Spanner.

APPLICATION

Sawing wood.

NOISE BUILD-UP

Noise (sound pressure level) in the workplace can exceed 85 dB. In this case, sound insulation and hearing protection measures must be taken by the operator.

ASSEMBLY INSTRUCTIONS

BE SURE TO DISCONNECT THE TOOL FROM THE POWER SUPPLY BEFORE ATTACHING OR REMOVING THE SAW BLADE. BE SURE THAT THE TEETH OF THE SAW BLADE ARE POINTING UPWARD AT THE FRONT OF THE TOOL.

ATTACHING AND REMOVING

THE BLADE (FIGURES 2, 3, 4, AND 5)

TTACHING THE BLADE

1.Pressing the spindle lock button (1), turn the hex-head bolt (2) with the spanner (3) until the spindle locks. (Fig.2)

2.Loosen the hex-head bolt by turning the spanner anticlockwise while pressing the spindle lock button. (Fig.2)

3. Remove the hex-head bolt and the outer blade washer (4). (Fig. 2)

4.Retract the lower guard (5) back with the lower guard lever (6) as far as possible under the upper guard (7). (Fig. 3)

5.Then, attach the saw blade (8) against the inner blade washer (9) on the spindle. Then fit the outer blade washer and the hex-head bolt. (Fig. 3 and 4)

GB

WS-6613 / WS-6613 / WS-6615X

13