Craftsman 358.351080 GAS Chain SAW Storage Instructions, Fuel System, Internal Engine, Other

Page 27

STORAGE

Immediately prepare your unit for storage at the end of the season or ff it will not be used for 30 days or more,

WARNING:

ALLOW THE ENGINE TO COOL, AND

SECURE THE UNIT BEFORE STORING OR

TRANSPORTING IN A VEHICLE.

STORE UNIT AND FUEL IN AN AREA

WHERE FUEL VAPORS CANNOT REACH

SPARKS OR OPEN FLAMES FROM WATER

HEATERS, ELECTRIC MOTORS OR SWITCH -I

STORE UNIT WITH ALL GUARDS IN PLACE.

POSITION SO THAT ANY SHARP OBJECT

CANNOT ACCIDENTALLY CAUSE INJURY

TO PASSERS BY.

STORE THE UNIT OUT OF THE REACH OF

CHILDREN.

GAS CHAIN SAW STORAGE INSTRUCTIONS

if your chain is to be stored for a period of time, clean it thoroughly pdor to storage. Remove any dirt, sawdust, leaves, oi!, grease, etc. Store in a clean dry area.

•Clean the entire unit.

•Clean air filter.Refer to =Customer Responsibilities."

•Inspectthe bar clamp area and clean any dirt, sawdust, grass,or debris that has collected. Inspect the guide bar and chain; replace a guide bar that is bent, warped, cracked, broken, or damaged in any other way. Replace a damaged or worn chain.

•Lightly oil external metal surfaces to prevent rust from forming.

handling chain. The chain is sharp and can

_h CAUTION: Wear protective gloves when cut you even when it is not moving.

•Apply a coating of oil to the entire surface of the guide bar and chain; wrap it in heavy paper or cloth.

•Be sure all handles and guards are in place and are

- ._.j

securely fastened. Replace any damaged parts.

FUEL SYSTEM

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur to fuel system com- ponents.Follow these instructions:

°Drain the fuel from the unit into an approved fuet con- tainer.

•Drain the fuel lines and carburetor by starting the engine and letting it run until it stops.

•Allow the engine to cool before storage.

IMPORTANT: It is importantto prevent gum deposits from formingin essentialfuel system parts such as the carbure- tor, fuel filter, fuel hose or tank during storage. Also, expe- dence indicatesthat alcohol blended fuels, those that use

ethanol or methanol (called gasohol or oxygenated fuel), can attract moistureand form acidic gas which willdamage your engine. To avoid engine problems, the fuet system should be emptied beforestorage of 30 days or longer.

Fue! stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add sta- bilizer to the gasolinein the fuel tank or fuel storage con- tainer.Always follow the mix instructionsfound on stabilizer containers.Run engine at least 5 minutes after adding sta- bilizer to allow the stabilizerto reach the carburetor.

CRAFTSMAN 40:1 2-cycle engine oil (AIR-COOLED) is specially blended with fuel stabilizer.If you do not use this Sears oil, you can add a fuel stabilizer to your fuel tank.

INTERNAL ENGINE

•Remove spark plug and pour t teaspoon of 40:1 2-cycle engine oil (AIR-COOLED) through the spark ptugopen- ing.Slowly pullthe starter rope 8 to 10 times to distribute oil to inner engine surfaces.

•Replace spark plug with a new one of the recommended type and heat range. Refer to "Product Specifications."

•Clean air filter.Refer to =CustomerResponsibilities."

•Re-install all covers and hardware removed for access; tighten all screwsand fasteners.

•Check entire unit for loose screws, nuts, and bolts- Replace any damaged, broken, or worn pads.

•Lightly oil external metal surface to prevent rust from forming.

•Use fresh fuel having the proper gasoline to oil ratio at the beginningof the next season.

OTHER

•Do not store gasolinefrom one season to another.

•Replace your gasolinecan if your can starts to rust.Rust and/or dirt in yourfuelsystem will cause problems.

•Store your unit i_a well ventilated area and covered, if possible, to prevent dust and dirt accumulation. Do not cover with plastic.Plastic cannot breathe and will induce condensationand eventual rust or corrosion.

IMPORTANT: NEVER COVER UNIT WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

•c

-27-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Result in Serious Injury 358.351080-18 358.351160-16Hours CST Lk WarningFuel Handling NightKnow Your SAW Plan AheadKickback Transporting and StorageUnderstanding Reactwe Forces Safety RulesKickback Safety Features Reduce the Chance of KickbackFull ONE Year Warranty on Craftsman GAS Chain SAW Customer ResponsibilitiesSPECIAL Notice Index Table of ContentsCarton Contents Operation Chain TravelDirection Howto USE Your Chain SAW Chain Oiler FigTHROnLE Control Group Fig Gasoline Fuel Mixture ChartBefore Starting Engine 401 2-CYCLE AIR-COOLED Engine OIL Guide BAR and Chain OILRight Foot through Opening in Rear Handle Starting a Warm EngineDifficult sTARTlinG or Flooded Engine FullTo Avoid PULL-IN Avoid Reactive Pinch ForcesGeneral Operation Tips To Avoid PINCH-KICKBACKOHAMMER to Force the Felling CUT PEN. the Wedge will Hold Tree FellingDetermine the Natural Fall Direction Felling TipsFelling Safety Operation SafetyBucking on the Ground Fig Bucking SafetyBucking Types of Cutting FigNever Cumb Into a Tree Tolimb or Pruning and LimbingPruning Fig Pruning and Limbing TipsCheck for Loose Fasteners and Parts Maintenance ScheduleBefore USE Check for Damaged or Worn PartsChain Gauge Customer ResponsibilitiesCrrftsmrn Sharpening CHAIFure20Side Plate File HolderInside HolderYearly Clean Unit and LabelsAfter USE Every 25 HoursFuel Line Barrel Service and Adjustments Chnn Adjustment , 41,42 & do43notBar Clamp Nuts Fan Housin Pulley Starter Rope Replacement , 45, 46, 47Housing Starter Rope NutsScrew ToolRewind for LOW Speed Mixture ADJUflTME Carburetor AdjustmentsIdle Speed Adjustment is marked with the letter T Idle Speed Adjustment MixtureAcceleration Check Adjusting Procedure Idle Speed Adjustment TLOW Speed Mixture Adjustment L After completing adjustments, check for accelerationInternal Engine StorageGAS Chain SAW Storage Instructions Fuel SystemTrouble Shooting Chart Symptom Cause Correction Trouble Shooting PointsLargeDa Repair PartsBarAdjungKit AssyUmirCo-.ow S30-037733 Foam-Nr FilterClp GrnerRepair Parts 358.351080 358.351160 358.351180 Ifyou Need Repair Service or PartsRepair Service 1-800-4-REPAIR Customer Assistance

358.351080 specifications

The Craftsman 358.351080 is a versatile and reliable gas-powered string trimmer designed for both residential and light commercial use. This trimmer is particularly beloved for its robust performance and user-friendly features, making it an essential tool for maintaining a well-kept lawn or garden.

One of the standout characteristics of the Craftsman 358.351080 is its powerful 32cc, 2-cycle engine. This engine provides ample power to tackle tough weeds, thick grass, and even small brush. Despite its strength, the engine is designed to be fuel-efficient, which translates to longer operating times and fewer fuel refills. The use of a 2-cycle engine means that users will need to mix oil with the gasoline, but this also provides a lightweight and compact design that makes handling easier.

A key feature of the Craftsman 358.351080 is its easy-to-use starting system. This trimmer incorporates an ergonomically designed starting mechanism that aids in quick and effortless ignition, reducing the frustration often associated with starting gas-powered tools. The inclusion of an automatic choke system further enhances this ease of use, ensuring that the engine runs smoothly from the first pull.

The Craftsman 358.351080 also boasts a generous cutting swath of 17 inches. This large cutting diameter allows for efficient trimming, significantly reducing the time it takes to complete lawn maintenance tasks. Additionally, the trimmer is equipped with a dual line bump head which allows for easy line advancement; users can simply tap the head on the ground to release more cutting line when needed.

Comfort is another important aspect of the Craftsman 358.351080. The trimmer features a comfortable, adjustable handle that can be tailored to suit the user’s height and grip preferences. This not only ensures better control while trimming but also helps reduce fatigue during prolonged use. Furthermore, the lightweight design of the trimmer allows for easy maneuverability, making it suitable for various garden types and terrains.

Safety features are also integrated into the design of the Craftsman 358.351080, with protective equipment and safety switches to prevent accidental starts. This commitment to user safety makes it an excellent choice for inexperienced users or those looking to operate the trimmer for extended periods.

In summary, the Craftsman 358.351080 string trimmer is a powerful, efficient, and user-friendly tool. With its impressive engine performance, generous cutting swath, and focus on user comfort and safety, it is well-suited for a variety of landscaping tasks. Whether you are a homeowner or a light commercial operator, this trimmer delivers the reliability and effectiveness needed to keep your outdoor spaces pristine.
Top Page Image Contents