Homelite UT08951, UT08550 Starting and Stopping, To Stop the Engine, See Figures 7, For Help Call

Page 12

operation

STARTING AND STOPPING

See Figures 7 - 8.

Starting the product differs depending on whether the engine is cold or warm. Blower should be on a flat, bare surface for starting.

TO START A COLD ENGINE:

Place the throttle/stop lever in the high speed (   )

position.

Slowly press the primer bulb seven (7) times.

Rotate the choke dial clockwise to the FULL CHOKE

position.

NOTE: Each choke position is identified by a detent in

the housing.

Pull the starter grip sharply until engine attempts to run

(no more than 4 pulls).

Rotate the choke dial to the counterclockwise HALF

CHOKE position.

Pull the starter grip sharply until the engine runs.

choke dial

PRIMER

BULB

Fig. 7

Allow the engine to run for 10 seconds.

Rotate the choke dial counterclockwise to the RUN

­position.

Turn throttle/stop lever to desired speed.

NOTE: Move the throttle/stop lever to the (   ) position to run the blower at high speed. Move the throttle/stop lever to the (   ) position to run the blower at low speed. Blower speed decreases as the switch is moved closer to the low speed position and increases when the switch is moved closer to the high speed position.

TO START A WARM ENGINE:

Rotate the choke dial counterclockwise to the RUN ­position.

Place the throttle/stop lever in the high speed (   ) position.

Slowly press the primer bulb seven (7) times.

Pull the starter grip sharply until the engine runs.

TO STOP THE ENGINE:

See Figure 9.

run

THROTTLE/ STOP LEVER

half

CHOKE

full

CHOKE

HIGH SPEED

Fig. 8

Place the throttle/stop lever in the STOP (OFF) position.

if assistance is required STARTING THIS product:

Do not return this product to the retail store where it was purchased. Please call our Customer Service Department for any issues you may have.

For Help Call: 1-800-242-4672

WARNING:

Keep away from all hot surfaces of the blower. Failure to do so could result in possible serious personal injury.

LOW

SPEED

STOP (OFF)

 

POSITION

Fig. 9

 

Page 12

Image 12
Contents OPERATOR’S Manual UT08550/UT08951Table of contents IntroductionGeneral safety rules Specific safety rules Symbols Symbol Name ExplanationService Symbol Signal MeaningFeatures Product SpecificationsStarter Assembly Installing the Blower Tube InstalLING the handleInstalling the vacuum bag Installing the vacuum tubes To install the vacuum tubesSee Figures 5 Vacuum Tubes Screwscrew Hinge Threaded Hole Door UpperOperation ApplicationsFueling and Refueling the trimmer Fuel MixtureStarting and Stopping To Stop the EngineIf assistance is required Starting this product See Figures 7Operating the blower Proper Operating PositionVacuum Operation Proper Operating­ PositionMaintenance General MaintenanceCleaning the AIR Filter Screen LubricationCleaning the Exhaust Port and Muffler Spark PlugSpark Arrestor Fuel CAPTroubleshooting Problem Possible Cause SolutionWarranty Limited Warranty StatementYour Warranty Rights and Obligations Emissions Maintenance Schedule and Warranted Parts List This product was manufactured with a catalyst mufflerAIR Filter Assy Fuel Tank AssyPage Parts and Service California Proposition

UT08550, UT08951 specifications

The Homelite UT08951 and UT08550 are two robust string trimmers designed to make yard maintenance more efficient and user-friendly. These tools are part of Homelite's commitment to providing reliable and innovative outdoor power equipment that caters to both homeowners and landscaping professionals.

One of the most prominent features of the UT08951 and UT08550 is their lightweight design. Weighing in at just over 10 pounds, these trimmers are easy to maneuver, allowing users to trim grass, weeds, and overgrown vegetation with minimal fatigue. The ergonomic design ensures that users can maintain a comfortable grip during prolonged use, making it an excellent choice for larger landscaping tasks.

Both models are equipped with powerful motors that deliver high RPMs for cutting efficiency. The UT08951 features a 2-cycle engine, whereas the UT08550 utilizes a 4-cycle engine. The 2-cycle engine is lighter and often easier to start, making it suitable for quick yard maintenance tasks. In contrast, the 4-cycle engine provides increased torque and fuel efficiency, making it ideal for more extensive trimming jobs.

Another standout characteristic is their Quick Load Spool technology. This innovative design simplifies the process of reloading the cutting line, allowing users to spend less time on maintenance and more time getting the job done. The automatic line advancement feature ensures that the cutting line is consistently fed, enhancing productivity and cutting performance.

The adjustable cutting width on both models provides versatility, allowing users to choose between a wider or narrower cut depending on the task at hand, whether it’s edging along flower beds or tackling thick grass. The trimmers also feature a variety of cutting accessories, including different spool sizes and line types, to accommodate different needs and preferences.

For added convenience, the UT08951 and UT08550 are designed with easy-start technology. This feature reduces the effort required to start the engine, allowing users to spend less time preparing the tool and more time working in the yard. The models also come equipped with safety features, including a protective guard to shield users from debris and a safety switch that prevents accidental starts.

In summary, the Homelite UT08951 and UT08550 string trimmers combine power, efficiency, and user-friendly design, making them ideal choices for anyone looking to maintain their yard effectively. Whether you’re a weekend warrior or a professional landscaper, these models offer the features and technologies needed to tackle a variety of trimming tasks with ease.