Husqvarna 67521HVE owner manual Lawn Mower, Engine

MAINTENANCE

LAWN MOWER

Always observe safety rules when performing any main- tenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chem- icals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check rear drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both rear wheels.

BLADE CARE

For best results, mower blade must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE (See Fig. 15)

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air fi lter and carburetor are up.

3.Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter-clockwise.

5.Remove blade and attaching hardware (bolt, lock washer and hardened washer).

TO REPLACE BLADE (See Fig. 15)

1.Position blade on the blade adapter aligning the two

(2)holes in the blade with the raised lugs on the adapter.

2.Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine.

3.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

4.Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise.

•The recommended tightening torque is 35-40 ft. lbs.

IMPORTANT: BLADE BOLT IS HEATTREATED. IF BOLT NEEDS REPLACING, REPLACE ONLYWITH APPROVED BOLT SHOWN IN THE REPAIR PARTS SECTION OF THIS MANUAL.

BLADE
BLADE ADAPTER
	TRAILING
	EDGE
	HARDENED
	WASHER
LOCK
WASHER	BLADE BOLT

FIG. 15

TO SHARPEN BLADE

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause eventual damage to lawn mower or engine.

•The blade can be sharpened with a fi le or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, drive a nail into a beam or wall. Leave about one inch of the straight nail exposed. Place center hole of blade over the head of the nail. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

GRASS CATCHER

•The grass catcher may be hosed with water, but must be dry when used.

•Check your grass catcher often for damage or deterio- ration. Through normal use it will wear. If catcher needs replacing, replace only with approved replacement catcher shown in the Repair Parts section of this manual. Give the lawn mower model number when ordering.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classifi cation SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

							SAE 30
			5W-30
F	-20	0			30 32 40		60	80	100
C	-30	-20		-10	0	10	20	30	40
	TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
								il i	h 1

NOTE: Multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, and you should check your engine oil level frequently to avoid possible engine damage from running low on oil.

12