QUICK START GUIDE
EJ-FT820
Printed in Korea
GH68-47410D Rev.1.0
B Type 03/2017
English
a
f
b
c
g
d
e
A
B
Copyright © 2017 Samsung Electronics
•Please read this guide before using the device to ensure safe and proper use.
•Images may differ in appearance from the actual product. Content is subject to change without prior notice. Visit www.samsung.com to view device information, the latest guide, and more.
•The keyboard is optimized to connect with the SAMSUNG Galaxy Tab S3 and may not be compatible with other devices. Before connecting the keyboard with devices other than the SAMSUNG Galaxy Tab S3, make sure they are compatible with the keyboard.
•Your consumer rights are governed by the law of the country in which you purchased the product. Please contact your service provider for more information.
Package contents
Keyboard, S Pen holder, Quick start guide
Device layout
| Stand |
| S Pen holder slot |
|
|
|
|
| Rear camera hole |
| Dock ports |
|
|
|
|
| Connection hole |
| Keyboard |
|
|
|
|
| S Pen holder |
|
|
|
|
|
|
Attaching the S Pen holder
You can insert the S Pen into the S Pen holder attached to the S Pen holder slot.
Make sure that the S Pen holder is securely attached after 24 hours. Do not reuse the adhesive tape if it detaches from the surface.
Connecting the keyboard
When you connect the keyboard to a tablet, you can enter characters without pressing the tablet’s screen. You can also use the keyboard as a cradle for the tablet by using its stand.
1.Position the tablet’s rear camera to insert it into the rear camera hole and attach the tablet to the stand. (
2.Insert the tablet into the connection hole to meet the tablet’s connectors and the dock ports. (
Make sure not to disconnect the tablet and the keyboard accidentally or drop them while moving.
Safety information
Read all safety information before using the device to ensure safe and proper use. To view the full safety information, refer to the Samsung website.
The device contains magnets. The American Heart Association (US) and the Medicines and Healthcare Products Regulatory Agency (UK) both warn that magnets can affect the operation of implanted pacemakers, cardioverters, defibrillators, insulin pumps or other electro medical devices (collectively,“Medical Device”) within the range of 15 cm (6 inches). If you are a user of any of these Medical Devices, DO NOT USE THIS DEVICE UNLESS YOU HAVE CONSULTED WITH YOUR PHYSICIAN
Use
Do not drop or cause an impact to the device
The device can be used in locations with an ambient temperature of 0 °C to 35 °C. You can store the device at an ambient temperature of
Prevent the dock ports from contact with conductive materials, such as liquids, dust, metal powders, and pencil leads
Do not allow children or animals to chew or suck the device
Do not disassemble, modify, or repair your device
FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.