Desa Tech CG2618PV manuals

36 pages608.06 Kb

UNVENTED (VENT-FREE) PROP ANE/LP GAS LOG HEA TER
- CG3324PT, CG3630PT, CG2618PV, CG3324PV , and CG3630PV Thermostat and Variably-Controlled Models
  - Variably Control Models Also Designed Certified as Vented Decorative Appliance)
- OWNERS OPERATION AND INSTALLATION MANUAL
- 2CONTENTS
- SAFETY INFORMATION
  - DANGER
- 3SAFETY INFORMATION
  - WARNINGS
- 4PRODUCT IDENTIFICATION
- LOCAL CODES
- UNPACKING
  - Note:
- PRODUCT FEATURES
  - Unconfined Space
  - Confined Space
  - 5PROVIDING ADEQUATE VENTILATION
    - Unusually Tight Construction
  - 6DETERMINING AIR FLOW FOR HEATER LOCATION
    - Determining if You Have a Confined or Unconfined Space
      - National Fuel Gas Code, ANSI Z223.1, 1992, Section 5.3.
        IMPORTANT:
        Figure 3 - Ventilation Air from Outdoors
  - 7VENTILATION AIR
    - Ventilation Air From Inside Building
      - Rework worksheet, adding the space of the adjoining unconfined space.
      - The combined spaces must have enough fresh air to supply all appliances in both spaces.
      - Ventilation Air From Outdoors
        Figure 2 - Ventilation Air from Inside Building
- 8INSTALLING
  - CHECK GAS TYPE
  - 9INSTALLATION AND CLEARANCES (Vent-Free Operation Only)
  - LOG SIZING REQUIREMENTS
  - MINIMUM FIREPLACE CLEARANCE TO COMBUSTIBLE MATERIALS
    - Minimum Wall and Ceiling Clearances (see Figure 4)
      - Installing Damper Clamp Accessory for Vented Operation,
    - 10Minimum Non Combustible Material Clearances
      - (A)
    - 11Minimum Non Combustible Material Clearances
      - Accessories,
        Figure 6 - Minimum Mantel Clearances Without Using Hood
      - IMPORTANT:
        If Using Mantel
      - Between 8" and 12",
      - 14" Min.
      - Combustible Material Non-Combustible Material
      - Hearth 5" Min.
      - Combustible Material
      - 12Floor Clearances
        Figure 7 - Minimum Mantel Clearances When Using Hood
        Figure 8 - Minimum Fireplace Clearances If Installed at Floor Level
      - Figure 9 - Minimum Fireplace Clearances Above Combustible Flooring
      - Mantel Shelf
  - 13INSTALLING DAMPER CLAMP ACCESSORY FOR VENTED OPERATION
  - 14INSTALLING HEATER BASE ASSEMBLY
  - 15CONNECTING TO GAS SUPPLY
    - Pressure Testing gas Supply Piping system
      - Connecting to Gas Supply
  - 17CHECKING GAS CONNECTIONS
    - 18Pressure Testing Heater Gas Connections
      - Figure 15 - Manual Shutoff Valve
      - Figure 16 - Checking Gas Joints
  - 19INSTALLING LOGS
- 20OPERATING HEATER
  - FOR YOUR SAFETY READ BEFORE LIGHTING
  - LIGHTING INSTRUCTIONS
  - NOTICE
- 21OPERATING HEATER
  - TO TURN OFF GAS TO APPLIANCE
  - THERMOSTAT CONTROL OPERATION
    - (Thermostat-Controlled Models Only)
  - VARIABLE CONTROL OPERATION
- 22INSPECTING BURNERS
  - PILOT FLAME PATTERN
  - FRONT BURNER FLAME PATTERN
- 23CLEANING
- MAINTENANCE
  - ODS/PILOT AND BURNERS
  - LOGS
    - IMPORTANT:
    - IMPORTANT
    - 26POSSIBLE CAUSE
    - REMEDY
  - 27OPTIONAL POSITIONING OF THERMOSTAT SENSING BULB
    - For Masonry and Factory-built Metal Fireplace
  - 28OPTIONAL POSITIONING OF THERMOSTA T SENSING BULB
    - For Masonry and Factory-built Metal Fireplace
      - Figure 31 - Installing Thermostat Sensing Bulb behind Glass Doors
      - Do not crimp capillary.
- 29TECHNICAL SERVICE
  - SPECIFICATIONS
- SERVICE HINTS
  - Note:
- 30REPLACEMENT PARTS
- PARTS CENTRALS
- 31ACCESSORIES
- 32ILLUSTRATED PARTS BREAK- DOWN
  - Variably Controlled Models
- 33PARTS LIST
  - Variably Controlled Models
- 34ILLUSTRATED PARTS BREAK- DOWN
  - Thermostat- Controlled Models
- 35PARTS LIST
  - Thermostat- Controlled Models
- 36WARRANTY INFORMATION
  - LIMITED WARRANTY VENT-FREE PROPANE/LP GAS LOG HEATERS