Akai RMD-V3104U manuals

49 pages739.51 Kb

14CHAPTER 7. MVP MANUAL
- 1. INTRODUCTION
- 152. CONNECTION WITH MVP EXTERNAL COMPUTER
- 163. INSTRUCTIONS FOR USING A COMPUTER AS A TERMINAL
  - <When the IBM-PC/AT is used>
  - <With the PC-9800 series>
  - <Example of a program GW-BASIC>
  - <Communication mode settings in use of CCT98>
- 174. OPERATING MODES
- 195. MVP VIDEO OUTPUT MODES
- 206. ADJUSTMENT FUNCTIONS
  - (1) MVP settings
  - (2) NTSC input board setting
  - (3) Variable scan board settings
- 217. PICTURE FRAME ADJUSTMENT PROCEDURES
  - 1. Command reference
    - (3) To set the system back to 4-screen magnification [@ command]
      - NOTE) An input board must be added in order to display the image of the OPTION input. (Option)
  - 222. Adjusting the picture frame
    - (1) To perform fine adjustment of the picture frame [&G command]
    - 23(2) To perform coarse adjustments of the picture frame [&P2, &Q2 commands]
    - 24(3) To store the picture frame data [&W command]
    - (4) To load the picture frame data [&L command]
  - 253. To switch the image input [IFF command]
    - RGB Personal computer
  - 264. To indicate the current MVP state [SYS command]
  - 275. To perform NTSC input board picture quality adjustment
    - (1) To set the adjustment mode [AJYC command] (2) To exit the adjustment mode [AJN command]
    - 28(3) Bright compensation [BRT command]
    - (4) Color compensation [COL command]
    - (5) Tint adjustment [TNT command]
  - 296. Controls the panel switch function
    - (1) To set the manual mode [MNL command] (2) To set the remote mode [RMT command]
    - (3) To select composite video input [CIC command]
    - (4) To select YC separation input [YIC command]
    - (NOTE) With the RMD-V2550U, only standard speed input is possible.
    - 30(8) Optional variable scan board adjustment mode settings [:A command]
- 318. DEMO PATTERN SETTINGS AND CAUTIONS
- 329. INSTALLING AND REMOVING BOARDS
  - <Removal procedure>
  - For your safety
    - <Installation procedure>
    - 33<Board layout>
    - <Relationship between board insertion lanes and rear panel connectors>
- 3410. RMD-V3020 COMMAND REFERENCE
  - (1) Outline of the RMD-V3020
  - 35(2) VS board command rules
    - 0. Symbols
    - 1. Basic commands
    - 362. Exceptional commands
  - 37(3) Tracking adjustment [TRK command]
  - (4) Contrast adjustment [CNT command]
  - (5) R, G, B gain adjustment [RGN, GGN, BGN commands]
  - (6) Brightness adjustment [BRT command]
  - 38(7) B, R clamp adjustment [BLV, RLV commands]
  - (8) Blanking window level adjustment [BLK command]
  - (9) Horizontal, vertical direction screen display position adjustment [HPS, VPS commands]
    - AA
  - 39(10) Horizontal, vertical blanking window position adjustment [HWN, VWN commands]
  - (11) Horizontal, vertical blanking window width adjustment [HWD, VWD commands]
    - A A A
    - A A A
  - 40(12) Full dot number compensation [HFD command]
  - (13) Freeze frame Y:ON N:OFF [FZY, FZN commands]
  - (14) Vertical filter ON/OFF [DSY, DSN, DSX commands]
  - 41(15) Vertical compression filter conversion rate input [LCV command]
  - (16) Program ROM version display [VER command]
  - (17) To indicate the current function setting [STS command]
  - 42(18) To select preset model [M command]
  - 43(19) Model fresh [F command]
  - (20) Measurement data display [FRQ command]
  - 44(21) Model table reference [TBL command]
    - Note 1
    - Note 2
    - Note 4
    - Note 3
    - Note 2
    - Note 3 Note 1
  - 45(22) Horizontal frequency input [HFQ command]
    - Note 4
  - 46(23) Vertical frequency input [VFQ command]
  - (24) Vertical full-line input [VLN command]
  - (25) All reset [ARS command]
- 4711. MODE 99
- 4812. VS BOARD MODEL SELECTION
- 13. USING METHODS OF HFQ, VFQ, VLN
- 4914. SELECTING THE SYNC SIGNAL