2. Installation Guide lines
Onlyever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning optical parts, never
useindustrial strength cleaners on the projector’s optics as these will degrade optical coatings and damage sensitive optoelectronics
components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contam-
inants will culminate inextensive and irreversible ingrained optical damage. At this stage cleaningof the internal optical units will
be non-effective and impracticable. Damage of this nature is under no circumstances covered under the manufacturer’s warranty
andmay deem the warranty null and void. Insuch a case the client shall be held solely responsible for all costs incurred during any
repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne
particlesin the environment of the projector. Themanufacturer reserves the right to refuse repair if a projector has been subject to
wantful neglect, abandon or improper use.
Special Care for Laser Beams
Specialcare should be used when DLP projectors are used in the same room as performant laser equipment. Directorindirect hitting
ofa laser beam on to the lens can severe ly damage the Digital MicroMirror Devices™ in which case there is a loss of warranty
Which screen type ?
Thereare two major categories of screens used for projection equi pment. Those used for front projected images and those for rear
projection applications.
Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount
of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain.
The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10)
ormore. Thechoice between higher and lower gain screens is largely a matter of personal preference and another consideration
calledthe Viewing angle. Inconsidering the type of screen to choose, determine where the viewers will be located and go for the
highestgain screen possible. Ahigh gain screen will provide a brighter picture but reduce the viewing angle. For more information
about screens, contact your local screen supplier.
What image size? How big should the image be?
The projector isd esigned foran optimum screen width of :
• For CineVERSUM 60 : min 1.30 m (52”) to max 1.78 m (70”)
• For CineVERSUM 70 : min 1.55 m (61") to max 1.98 m (78”)
(dependingon theambient light conditions), with an aspect ratio of 16 to 9.
Dependingo n the used lens, the minimum and maximum diagonal screen sizes are :
For CineVERSUM 70
R9010080 Shortthrow lens (1.4 - 1.8) Min: 0.80m (32”) Max. 6.35 m (250”)
R9010081 Longthrow lens (1.8 - 2.4) Min : Wide : 1m (40”)
Min: Tele: 0.76 m(30”)
Max: Wide: 7.60 m (300”)
Max: Tele: 5.60 m (222”)
For CineVERSUM 60
R9002460 Shortthrow lens (1.7 - 2 .25) Min:1m(39”) Max.5 m (200”)
R9002461 Longthrow lens (2.25 – 3 ) Min: Wide: 0.8 m (32”)
Min: Tele: 0.60 m(24”)
Max: Wide: 6.0 m (240”)
Max: Tele: 4.50 m (178”)
2.3 Projector Configuration and Position
Which configuration can be used?
The projectorcan be installed to project images in four different configurations:
• Front/table
• Rear/table
• Front/ceiling
• Rear/ceiling
Positioning the projector
• The projector should be installed perpendicular with the screen on a distance PD and water leveled in both directions. The
mountingpositions in the following image is shown for a nominal lens position.
• Positionthe screen so that it is not in direct sunlight or room light. Lightfalling directly onto the screen washes out the colors,
makingviewing difficult . Closethe curtains and dim the lights when setting up the screen in a sunny or bright room.
• Theprojector lens should be centered horizontally in the middle of the screen.
8R5976763 CINEVERSUM60/70 22042004