7EUROPOWER PMP518M User Manual

[24]

 

 

 

 

 

 

 

 

{25]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[23]

[27]

 

 

[26]

Fig. 2.2: Rear panel control elements and connectors

2.4 Rear panel

[23]The mains connection is on a standard IEC receptacle. An appropriate power cord is supplied with the unit.

[24]FUSE HOLDER. Before connecting the unit to the mains, ensure that the voltage setting matches your local voltage. Blown fuses should only be replaced by fuses of the same type and rating. Please also read the information given in chapter 6 “Specifications”.

[25]The three PARALLEL SPEAKER OUTPUTs provide the mono main signal on a Neutrik Speakon-compatible connector (pins 1+/1- and 2+/2-) and on two 1/4" TS connectors.

The impedance of the loudspeaker connected must not fall below 4 Ω.

Information on how to properly connect your speaker with regard to polarity can be found on the rear of the mixer (PINOUTs).

[26]This is the cooling fan of the unit.

[27]SERIAL NUMBER.

3. Digital Effects Processor

100 FIRST-CLASS EFFECTS

The PMP518M features a built-in digital effects processor. This effects processor offers a large number of standard effects such as Hall, Chorus, Flanger, Delay and various combination effects. Using the FX control, you can feed signals into the effects processor. The integrated effects module has the advantage of requiring no wiring. This way, the danger of creating ground loops or uneven signal levels is eliminated at the outset, completely simplifying the handling.

Presets 00 - 09:

Hall

Presets 10 - 19:

Room

Presets 20 - 29:

Plate

Presets 30 - 39:

Gated/Reverse

Presets 40 - 49:

Early Reflections

Presets 50 - 59:

Delay

Presets 60 - 69:

Chorus

Presets 70 - 79:

Phase/Pitch

Presets 80 - 89:

Multi 1

Presets 90 - 99:

Multi 2

4. Installation

4.1 Mains connection

Blown fuses must be replaced by fuses of the same type and rating.

The mains connection is made using the enclosed power cord and a standard IEC receptacle. It meets all of the international safety certification requirements.

Please make sure that all units have a proper ground connection. For your own safety, never remove or disable the ground conductor from the unit or of the AC power cord.

4.2 Audio connections

The inputs and outputs of the BEHRINGER EUROPOWER are unbalanced 1/4" TS connectors — except for the balanced mono line inputs and the balanced XLR inputs. Of course, all inputs and outputs work with both balanced and unbalanced connectors. The Tape Ins and Outs are on RCA connectors.

Please ensure that only qualified personnel install and operate the power mixer. During installation and operation, the user must have sufficient electrical contact to earth. Electrostatic charges might affect the operation of the unit.

Unbalanced ¼" TS connector

Strain relief clamp

Sleeve

Tip

Sleeve (ground/shield)

Tip

(signal)

Fig. 4.1: 1/4" TS connector

behringer.com