Brother 4150CDN, HL-4140CN manual

		Before using this machine for the first time, read this Quick Setup	Quick Setup Guide
		Guide to setup and install your machine.
		To view the Quick Setup Guide in other languages, please visit
		http://solutions.brother.com/.	HL-4140CN
(EU Only)	ENG	Note: Not all models are available in all countries.
	Version 0		HL-4150CDN

Start Here

WARNING indicates a potentially

WARNING hazardous situation which, if not avoided, could result in death or serious injuries.

CAUTION indicates a potentially

CAUTION hazardous situation which, if not avoided, may result in minor or moderate injuries.

(HL‑4150CDN) In USA:

Please go to the Brother Solutions Center at http://solutions.brother.com/ and click Manuals on your model page to download the other manuals.

1 Unpack the machine and check the components

Note• The components included in the box may differ depending on your country.• We recommend that you save the original packaging.

• If for any reason you must ship your machine, carefully repack		Quick Setup Guide	Safety and Legal Booklet	AC Power Cord	Documentation/Installation
the machine in the original packaging to avoid any damage during					CD‑ROM(s)
transit. The machine should be adequately insured with the
carrier. How to repack the machine, see Shipment of the machine
in the User’s Guide.
• The interface cable is not a standard accessory. Buy the
appropriate interface cable for the interface you want to use (USB
or Network).
USB cable	Drum Unit	Waste Toner Box	Belt Unit	Starter Toner Cartridges
It is recommended to use a USB 2.0 (Type A/B) interface cable that
	(pre‑installed)	(pre‑installed)	(pre‑installed)		(pre‑installed)
is no longer than 2 meters (6 feet).
				(Black, Cyan, Magenta and Yellow)

Network cable

Use a straight‑through Category5 (or greater) twisted‑pair cable for 10BASE‑T or 100BASE‑TX Fast Ethernet Network.

WARNING

• Plastic bags are used in the packaging of your machine. Plastic bags are not toys. To avoid danger of suffocation, please keep these bags away from babies and children and dispose of them properly.

• This machine is heavy and weighs approximately 21.0 kg (46.3 lb.). To prevent possible injuries at least two people should lift the machine. Be careful not to pinch your fingers when you put the machine down.

• If you use a Lower Tray, carry it separately from your machine.

Note

Keep a minimum gap around the machine as shown in the illustration.

	200 mm (7.87 in.)
100 mm	100 mm	250 mm
(4.00 in.)	(4.00 in.)	(9.84 in.)

Remove the packing material from the machine

2			c. Press the front cover release
		IMPORTANT
		DO NOT plug in the AC power cord yet.		button and open the front cover.
				Remove the silica gel pack A.
	a. Remove the packing tape from the outside of the			CAUTION
		machine.		DO NOT eat Silica Pack. Discard
	b. Open the MP tray A, and remove the plastic sheet			immediately.
			d. Hold the green handle of the
		B from the MP tray support, then close the MP tray.
				drum unit and pull it out until it
				stops.
			e. Hold the orange packing
				material, and remove it.

f. Remove the 4 orange packing pieces.g. Push the drum unit firmly back into the machine.h. Close the front cover of the machine.

3 Load paper in the paper tray

a. Pull the paper tray completely out of the machine.

b. While pressing the green paper‑guide release lever A, slide the paper guides to fit the paper size you are loading in the tray. Make sure that the guides are firmly in the slots.

c. Fan the stack of paper well to avoid paper jams and misfeeds.

d. Put paper in the tray and make sure:The paper is below the maximum paper mark (▼▼▼) A.Over filling the paper tray will cause paper jams.The side to be printed on must be face down.The paper guides touch the sides of the paper so it will feed properly.

e. Put the paper tray firmly back in the machine. Make sure that it is completely inserted into the machine.

For more information about recommended paper, see Recommended paper and print media in the User’s Guide.

4 Print a test page

IMPORTANT

DO NOT connect the Interface cable yet.

a. Connect the AC power cord to the machine and then connect it to an AC power outlet.

b. Remove the label covering the machine’s power switch, and then switch the machine on.

c. After the machine has finished warming up, the LCD will show Ready.

Note

You can adjust the angle of the display by lifting it.

d. Press Go. The machine will print a test page. Check that the test page has printed correctly.

Note

This function will not be available after the first print job you send from your computer.

5 Set your language

a. Press + or − to choose General Setup. Press OK.b. Press OK to choose Local Language.c. Press + or − to choose your language. Press OK.

Now go toTurn the sheet over to install the printer driver.

Options

The machine has the following optional accessories. You can expand the capabilities of the machine by adding these items. For more information about the optional Lower Tray Unit and compatible SO‑DIMM Memory, visit us at http://solutions.brother.com/.

For installing the SO‑DIMM Memory, see Installing extra memory in the User’s Guide.

Lower Tray Unit (LT‑300CL)	SO‑DIMM Memory
Second lower paper tray unit can hold up to	You can increase the memory
500 sheets of paper. When the tray is installed,	by installing one SO‑DIMM
the machine expands total input capacity up to	(Small Outline Dual In‑line
800 sheets.	Memory Module).

Consumables

When the time comes to replace consumable items, an error will be indicated by the LCD on the control panel. For more information about the consumables for your machine, visit us at http://www.brother.com/original/ or contact your local Brother reseller.

Toner cartridges Drum unit

Belt Unit (BU‑300CL) Waste Toner Box (WT‑300CL)

For Network Users

Web Based Management (web browser)

The Brother print server is equipped with a web server that allows you to monitor its status or change some of its configuration settings, using HTTP (Hyper Text Transfer Protocol).

Note

• The login name for the Administrator is ‘admin’ (case sensitive) and the default password is ‘access’.

• We recommend Microsoft® Internet Explorer® 6.0 (or greater) or Firefox 3.0 (or greater) for Windows® and Safari 3.0 (or greater) for Macintosh. Please also make sure that JavaScript and Cookies are always enabled in whichever browser you use. To use a web browser, you will need to know the IP Address of the print server. The IP Address of the print server is listed on the Print Setting Page.

a. Type http://machine_ip_address/ into your browser (where machine_ip_address is the IP Address or the print server name).

For example: http://192.168.1.2/See Web Based Management in the Network User’s Guide.

Reset the network settings to the factory default

To reset all network settings of the print server to its factory default, follow the steps below.

a. Press + or − to choose Network. Press OK.b. Press + or − to choose Network Reset. Press OK.c. Press + to choose Reset.d. Press + to choose Yes for reboot. The machine will re-start.

For replacing the consumable items, see Replacing consumable items in the User’s Guide.