Brother LS6233040 manual

	Before you can use the machine, read this Quick Setup Guide	Quick Setup Guide
	for the correct setup and installation.	DCP-385C
LS6233040
ARL/ASA/NZ
Printed in China

Start Here

Important

DO NOT connect the USB cable yet.

Warnings tell you what to do to WARNING prevent possible personal injury.

Unpack the machine and check the components

1	Note		b. Remove the green protective packing a
			by lifting the front of the machine and then
	• The components of your box may differ depending on your
			pulling down on the packing part.
		country.
	•	Save all packing materials and the box in case for any
		reason you must ship your machine.

• Your machine has a USB interface that is compatible with the USB 2.0 specification.

• To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is properly grounded through the standard electrical wiring. Non grounded equipment may cause an electrical shock hazard, and may cause excessive electrical noise radiation.

	1
a. Remove the protective tape and film.	c. Remove the plastic bag b containing the ink
	cartridges from on top of the paper tray.

d.Make sure you have all components.

2	Inbox Ink
	Cartridges [x4]1
	Black
	Yellow
	Cyan
	Magenta
Power Cord	CD-ROM
USB	User’s Guide
Interface
Cable
Quick Setup
Guide

1Approx. 65% yield of the replacement cartridge. For details, see Consumable items in the User’s Guide.

Australia & New	Hong Kong,	Philippines &
	Malaysia &
Zealand		Thailand
	Singapore
The supplied mains plug is a		The supplied mains plug is
grounded three pin plug.		a side grounded two pin plug.

WARNING

Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep these bags away from babies and children.

Load plain A4 paper

2 a. Pull out the paper tray. b. Lift the paper tray cover a.

1

c.Press and slide the paper side guides a and paper length guide b to fit the paper size.

Make sure that the triangular marks c on the paper side guides a and paper length guide b line up with the mark for the paper size you are using.

1

3

2

3

Important

Do not push the paper in too far.

d.Fan the stack of paper well.

e.Gently put the paper into the paper tray. Check that the paper is flat in the tray.

f.Gently adjust the paper side guides to the paper with both hands.Make sure the paper side guides touch the edges of the paper.

g.Close the paper tray cover and slowly push the paper tray back into the machine.

h.Pull out the paper support a until it clicks, and then unfold the paper support flap b.

2

1

Connect the power cord

3 a. Connect the power cord.

WARNING

The machine must be fitted with an earthed plug.

Important

DO NOT connect the USB cable yet.

Note

The control panel warning LED will stay on until you have installed the ink cartridges.

Set the language (not available for Hong Kong users)

4	a. After connecting the power				b. Choose Yes or No and press
		cord, the LCD shows:				OK.
		Select Language				English
		English				Yes
		Français				No
		Deutsch
		Nederlands
		Italiano
		Select Language	Select & Press	OK		Select Language	Select & Press OK

Press a or b to choose your language and press OK.

Note

•The languages available may differ depending on your country.

•If you set the wrong language, you can change it again after setting the date and time. (For details see Changing LCD language in Chapter 3 of the User’s Guide.)

Install the ink cartridges

5 a. The LCD shows:c. Remove the green protective part a.

No Cartridge

Install Ink

Black

b. Open the ink cartridge cover a.

11

d.Unpack the ink cartridge.

Turn the green knob on the protective yellow cap clockwise until it clicks to release the vacuum seal, then remove the cap a.

1

e. Install each ink cartridge in the direction of the arrow on the label.Take care to match the colour of the lever a with the cartridge colour b.

1

2

f.Gently push the ink cartridge until it clicks. After all the ink cartridges are installed close the ink cartridge cover.

Important

After initial installation of the ink cartridges, the machine will start cleaning the ink tube system. This cleaning process will last approximately four minutes. DO NOT unplug the machine from the power outlet or attempt to stop the cleaning process. Interruption of cleaning process may cause undesired print quality problems.

Check the print quality

6 a. When the preparation process has finished, the LCD shows this message.

Set Paper and Press

Start

Press Colour Start.

b.Check the quality of the four colour blocks a on the sheet. (black/yellow/cyan/magenta)

1

OK

o If all lines are clear and visible, press (Yes) to finish the quality check.

Set the LCD contrast (If needed)

7 a. Press Menu.b. Press a or b to choose General Setup. press OK.c. Press a or b to choose LCD Settings. press OK.d.Press a or b to choose LCD Contrast.e.Press d or c to choose Light, Med or Dark. press OK.f.Press Stop/Exit.

Set the date and time

8 a. Press Menu.b. Press a or b to chooseInitial Setup, and then press OK.c. Press a or b to choose Date&Time, and then press OK.

Note

d.Press a or b repeatedly to enter the last two digits of the year, and then press OK.

Date&Time

Year:20

08

MENU Input & Press OK

(e.g. Enter 08 for 2008.)

e. Repeat for Month and Day, and Hours and Minutes

in 24-hour format.

o If you can see missing short lines, press (No) and follow the steps on the LCD.

Poor

Note

You can also adjust the angle of the display by lifting it.

If you make a mistake and want to start again, press Stop/Exit to go back to step a.

f. Press Stop/Exit. Turn the sheet over.