3. FUNCTION SETTINGS
No. | Initial value | Setting range | Setting details |
| |
111 | 1000 (rpm) | 500 - 2000 | Limit speed for sewing patterns with changed sewing pitch (T stitches) |
| |
Needle lifting and needle lowering are carried out at low speed when No. 110 | |||||
|
|
| is set to “1”. |
| |
|
|
| Low speed limit when sewing machine motor starts |
| |
112 | 1 | 0 - 1 | 0: No limit |
| |
1: When not at the needle up or needle down position, the needle bar speed is | |||||
|
|
| |||
|
|
| limited to low speed until the needle up or needle down position |
| |
113 | 0 | 0 - 1 | Changing speed using speed bar while sewing machine motor is operating | ||
0: Can be changed |
| ||||
|
|
| 1: Cannot be changed |
| |
|
|
| Operation when auto function is on (fixed stitch/name label sewing) |
| |
114 | 0 | 0 - 1 | 1: Automatic thread trimming is not carried out after fixed stitch/name label | ||
sewing is complete |
| ||||
|
|
| 0: Automatic thread trimming is carried out after fixed stitch/name label sewing | ||
|
|
| is complete |
| |
|
|
| On time for |
| |
115 | 1.0 | 0.1 - 4.9 | Presser foot lifting |
| |
|
| ||||
(1.0 ms) | (0.1 - 4.9 ms) |
|
| ||
| (Fully on) |
| |||
|
|
|
| ||
|
|
| Enabled when No. 37 is set to “0”. | 2264M | |
|
|
| On time for |
| |
116 | 2.5 | 0.1 - 4.9 | Presser lifting |
| |
|
| ||||
| (2.5 ms) | (0.1 - 4.9 ms) | (Fully on) |
| |
|
|
|
| ||
|
|
| Enabled when No. 37 is set to “1” | 2265M | |
|
|
| On time for quick reverse solenoid during chopping |
| |
117 | 1.1 | 0.1 - 4.9 | Quick reverse solenoid |
| |
(1.1 ms) | (0.1 - 4.9 ms) |
|
| ||
| (Fully on) |
| |||
|
|
|
| ||
|
|
|
| 2266M | |
|
|
|
|
| |
118 | 85 | 40 - 100 | Fully on time for quick reverse solenoid |
| |
|
| ||||
(85 ms) | (40 - 100 ms) |
|
| ||
|
|
| |||
|
|
|
|
| |
119 | 1 | 0 – 2 | Correction level when |
| |
correction) |
| ||||
|
|
| * Enabled when zigzag width setting is 4.0, 4.2, … |
| |
120 | 2 | 0 - 3 | Correction level when | ||
correction) |
| ||||
|
|
| * Enabled when zigzag width setting is 4.8 or higher |
| |
121 | 1 | 0 - 2 | Correction level when | ||
correction) |
| ||||
|
|
| * Enabled when zigzag width setting is 4.1, 4.3, … |
| |
123 | 45 (degrees) | 30 - 90 | Servo lock release rotation angle [Do not change this setting.] |
| |
(degrees) |
| ||||
|
|
|
| ||
11 |