3. FUNCTION SETTINGS
Memory switch No. 125 - 148No. | Initial value | Setting range | Setting details | |||
|
|
| Servo lock operation | |||
125 | 0 | 0 - 1 | 0: None | |||
1: When stopped | ||||||
|
|
| ||||
|
|
| 2: When presser foot lifting signal is on | |||
126 | 1 (seconds) | 0 - 120 | Servo lock timer setting | |||
0: No timer operation | ||||||
(seconds) | ||||||
|
| |||||
|
|
| ||||
127 | 100 (hours) | 0 - 500 | Time from when | |||
(hours) | ||||||
|
|
|
|
| ||
|
|
| Flicker reduction function (if fluorescent light is flickering) | |||
128 | 0 | 0 - 3 | 0: None | |||
1: “Medium” flicker reduction effect | ||||||
|
|
| 2: “Small” flicker reduction effect | |||
|
|
| 3: “Large” flicker reduction effect | |||
129 | 0 | Gain during motor acceleration [Do not change this setting.] | ||||
130 | 0 | Gain during motor deceleration [Do not change this setting.] | ||||
131 | 700 (hours) | 0 - 1200 | ||||
(hours) | ||||||
|
|
|
|
| ||
137 | 20 (degrees) | 0 - 40 | Thread trimmer on timing | |||
(degrees) | (*) Angle from needle drop signal | |||||
|
| |||||
138 | 40 (degrees) | 0 - 120 | Upper thread feeding on timing | |||
(degrees) | (*) Angle from needle drop signal | |||||
|
| |||||
139 | 40 (ms) | 0 - 40 (ms) | Thread trimmer off timing | |||
(*) Time from needle up stop | ||||||
|
|
| ||||
140 | 40 (ms) | 0 - 100 (ms) | Upper thread feeding off timing | |||
(*) Time from needle up stop | ||||||
|
|
| ||||
141 | 30 (ms) | 5 - 60 (ms) | Quick reverse solenoid on response time for T stitches | |||
142 | 30 (ms) | 5 - 60 (ms) | Quick reverse solenoid off response time for T stitches | |||
143 | 30 (ms) | 0 - 60 (ms) | Upper thread feeding solenoid fully on time | |||
(*) No chopping when set to “0” | ||||||
|
|
| ||||
|
|
| On time for upper thread feeding solenoid during chopping | |||
144 | 1.0 | 0.1 - 4.9 | Upper thread | |||
feeding Solenoid | ||||||
(1.0 ms) | (0.1 - 4.9 ms) | |||||
|
| (fully ON) |
| |||
|
|
|
|
| ||
|
|
|
|
| 0123B | |
|
|
|
|
| ||
|
|
|
|
|
| |
145 | 1 | 0 - 1 | Needle up stop position error display function after thread trimming | |||
0: None | ||||||
|
|
| 1: Yes ([Err 111] is displayed.) | |||
146 | 4 | 4 - 14 | Needle zigzag sync position (angle from needle up stop signal turning off x 8 | |||
degrees) | ||||||
|
|
| ||||
147 | 0 | 0 - 5 | Needle zigzag sync delay | |||
(degrees) | ||||||
|
|
|
|
| ||
|
|
| Machine head fan | |||
148 | 1 | 0 - 1 | 0: Stopped | |||
1: Operating (stops when machine head is tilted back and when an error | ||||||
|
|
| ||||
|
|
| occurs) | |||
12 |