Campbell Hausfeld CHN10401 6

Operating Instructions

Operating the Tool			2.	For shallow			3.	Undo latch by
(Continued)				penetration,	(C)			pulling out
LOADING/UNLOADING THE TOOL				turn the	(C)			and down. The
				turn the				and down. The
				wheel (C)				wire latch will
1. Always disconnect the tool from				wheel (C)				wire latch will
1. Always disconnect the tool from				to right to				disengage from
the air supply before loading				to right to				disengage from
the air supply before loading				the extent				the hooks on the nose.
fasteners.				the extent				the hooks on the nose.
fasteners.				desired.			4.	The door can
2. Push down				desired.

		Latch	3.	For deeper				now be rotated,
on the latch		Latch	3.	For deeper				now be rotated,
on the latch		button		penetration,				exposing
button. Pull				penetration,				exposing
button. Pull				turn the wheel (C) to left to the				the jammed
back on the				turn the wheel (C) to left to the				the jammed
back on the				extent desired.				fastener.
magazine cover.				extent desired.				fastener.
magazine cover.			4.	Make sure trigger			5.	Remove the
3a. For nails, insert			4.	Make sure trigger			5.	Remove the
3a. For nails, insert				and work contact				jammed
a stick into				and work contact				jammed
a stick into				element (WCE) move				fastener, using
the magazine.				element (WCE) move				fastener, using
the magazine.				freely up and down		Movement		pliers or a
Make sure the				freely up and down		Movement		pliers or a
Make sure the				without binding or				screwdriver if
pointed ends				without binding or				screwdriver if
pointed ends				sticking after each				required.
of the fasteners are resting on the				sticking after each				required.
of the fasteners are resting on the				adjustment.			6	Rotate door
bottom ledge of the magazine when				adjustment.

								back into the
loading. Make sure the nails are not			Adjusting The Direction Of The					back into the
dirty or damaged.			Exhaust					closed position.
3b. For staples, load			The tool is
a clip of staples			equipped with				7.	Extend the wire
with the crowns			an adjustable				7.	Extend the wire
with the crowns			an adjustable					latch and place
straddling the			direction exhaust			Rotate		latch and place
straddling the	Magazine		direction exhaust					over the hooks
magazine rail.			deflector. This is					over the hooks
								on the nose.
	rail
	rail		intended to allow
			intended to allow
4. Push the			the user to change the direction of the				8.	Close the latch
4. Push the			exhaust. Simply twist the deflector to
magazine cover
								by pushing the
			any direction desired.
forward until
								latch up and

latch button
latch button			CLEARING A JAM FROM THE TOOL					in until the
pops up.			CLEARING A JAM FROM THE TOOL					in until the
pops up.			1.	Disconnect the				latch snaps into
5. Always unload all fasteners before			1.	Disconnect the				latch snaps into
5. Always unload all fasteners before				air supply from				place.
removing tool from service.				the nailer.			9.	Make sure the
Unloading is the reverse of loading,				the nailer.			9.	Make sure the
Unloading is the reverse of loading,								trigger and
except that you must disconnect								trigger and
except that you must disconnect								work contact
the air supply before unloading.			2.	Remove all				work contact
the air supply before unloading.			2.	Remove all				element (WCE)
				fasteners from				element (WCE)
ADJUSTING THE FASTENER				fasteners from				move freely
ADJUSTING THE FASTENER				the magazine				move freely
PENETRATION				the magazine				up and down
PENETRATION				(see “Loading/				up and down
The tool is equipped with an adjustable				(see “Loading/				without sticking or binding.
				Unloading The				without sticking or binding.

depth of drive feature. This allows the
depth of drive feature. This allows the				Nailer”).
user to determine how deep a fastener				Nailer”).
user to determine how deep a fastener					Failure to remove
will be driven into the work surface.					Failure to remove
will be driven into the work surface.					all fasteners will
					all fasteners will
1. Adjust operating pressure so			cause the fasteners to eject from the
fasteners are driven consistently. Do			front of the tool.
not exceed 100 psi.