INSTRUCTIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTRUCCIONES

 

 

 

 

E-IM-2471

 

 

 

 

 

 

 

PRINTED IN CHINA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BEFORE STARTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1)Remove the insulation tape at the back of calculator. (Figure a )
2)Remove the tape on the ink ribbon of calculator. (Figure b , c )
3)Plug in AC power cord. (Figure d)
4)Turn the power switch on. (Figure e )
5)Press [RESET] key before use. (Figure f )

DECIMAL POINT SELECTOR SWITCH

– Used for designating the decimal point position (+ 0 2 3 4 6 F) for calculated results.

+ (Add-Mode)Addition and subtraction functions are performed with an automatic 2-digit decimal. It is convenient for currency calculations.

F (Floating Decimal Point) – All effective numbers up to 12 digits are printed or displayed.

ROUNDING SWITCH

– Used for round-up [ ] , round-off [5/4], or round-down [ ]to the pre-selected decimal digits in the result.

ANTES DE EMPEZAR

ESPAÑOLA

 

 

a

b

c

d

e

f

INTERRUPTOR SELECTOR DE PUNTO DECIMAL

CONMUTADOR DE REDONDEO

a

b

c

d

e

f

INSTALLING PRINTING PAPER

Note : Turn the power off
1) Remove the printer cover (Figure ) and lift up the paper arm (Figure ).
2)Replace the printer cover (Figure ).
When inserting the paper, cut the edge of the paper as shown (Figure ).

3)Place the new paper roll on the arm. The edge of the paper should be positioned as shown (Figure ).

Suitable paper roll -- Width : 57mm (2-1/4”) / Diameter: 86mm (3-3/8”)
4)Insert the paper into the slit located of the machine as indicated (Figure ).
5) Turn the power switch on (Figure ). Press the paper feed key

to advance

the paper (Figure ).

 

REPLACING THE INK RIBBON

Note: Turn the power off.
1)Remove the cover and lift up the paper arm.
2)Lift ribbon spools off the shafts. Discard the old ribbon and spools.

3)Place the ribbon spool on the left spool pin and push it down until it clicks.

4)Thread the ribbon along the outer edge of the side guide, making sure that the black half of the ribbon is still on the top.

5)Place the ribbon between the printing ring and printing roller. Thread the ribbon along the outer edge of the left side guide.

6)Place the other ribbon spool on another spool pin.
7)Push the spool down until it clicks.
8)Take up any ribbon slack by rotating the left spool counterclockwise.
9)Replace the printer cover.

GRAND TOTAL / RATE SET SWITCH

GRAND TOTAL

– When the calculations are performed with the GT switch set to "ON", the total(s) are accumulated in the grand total memory. Each time is pressed, the subtotal number is printed with the symbols G+. When is pressed, the intermediate grand total is printed with the symbols G. Press successively to get the grand total followed by the symbols G.

TAX RATE SET
– Set switch to "TAX RATE SET" for setting or recalling the TAX rate.

PRINT / ITEM COUNT SWITCH

Print Off – Entries and results will appear on the display, but will not be printed out.

Print On – Entries and results will appear on the display and will be printed out.

Item – Set switch to "ITEM" to count the number of times the

, , and keys have been pressed. The item count will be printed on the left hand side of the paper roll (up to 999 times) when the, , or keys are pressed.

OVERFLOW

In the following cases, when "E" is displayed, "ERR" is printed, the keyboard is electronically locked, and further operation is impossible.

Press to clear the overflow. The overflow occurs when:

1.The result or the memory content exceeds 12 digits to the left of the decimal point.

2.Dividing by "0".

3.The sequential operation speed is faster than the calculation processing speed. (Buffer Register Overflow)

Electromagnetic interference or electrostatic discharge may cause the display to malfunction or the memory, currency rate and tax rate to be lost or altered. Should this occur, use the tip of a ballpoint pen

(or similar sharp object) to press the [RESET] button on the back of the calculator. After resetting be sure to set the calendar, clock and tax rate again.

INSTALANDO PAPEL DE IMPRESIÓN

COMO CAMBIAR LA CINTA

TECLA DE GRAN TOTAL / RATE SET

IMPRESIÓN / RECUENTO ITEM

FUNCIÓN DE REBOSE

“ERR”

ESPECIFICACIONES

IMPORTANT: Use only the same type of ribbon spools.

REPLACING BACKUP BATTERY

Memory backup battery retains the tax rate, calendar and clock setting, when the power is off or even when the AC cord is disconnected.

Battery : 1 Lithium battery (Type : CR2032)
Battery life : Backup time 2000 hours Replace back-up battery

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instruction.

SPECIFICATION

Power Source: AC120V, 60Hz
Operation Temperature: 0°C to 40°C (32°F to 104°F)
Calculating Capacity: 12 digits maximum

Dimension: 320mm (L) x 193 mm (W) x 71mm (H) / 12-39/64" (L) x 7-39/64" (W) x 2-51/64" (H)

Weight: 1,532 g (3.37 lbs)
(Subject to change without notice)

The socket-outlet shall be installed near the equipment and shall be easily accessible.

For CA, USA Only

Included battery contains perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for detail.

The top case, bottom case, printer cover and battery cover in this product are made from recycled Canon copier plastic.

REEMPLAZO DE LA BATERÍA DE RESPALDO

AC120V, 60Hz

320mm (An) x 193 mm (Pr) x 71mm (Al) / 12-39/64" (An) x 7-39/64" (Pr) x 2-51/64" (Al)

Peso: 1,532 g (3.37 lbs)

La toma de corriente debe instalarse cerca del equipo y debe ser fácilmente accesible.

Para el Ca, los E.E.U.U. Solamente

La batería incluida contiene el material del perclorato - El manejo especial debe ser aplicado.Para el detalle, por favor ver http://www.dtsc.ca.gov/hazardouswaste/perchlorate