MP27DII
INSTRUCTIONS E
INSTRUCCIONES ES
DECIMAL POINT SELECTOR SWITCH
• Used for designating the decimal point position (+, 0, 2, 3, 4, 6, F) for calculated results.
• + (ADD-MODE)
Addition and subtraction functions are performed with an automatic
• F (FLOATING DECIMAL POINT)
All effective numbers up to 12 digits are printed or displayed.ANTES DE EMPEZAR | ESPAÑOL |
|
|
a | b | c |
INTERRUPTOR SELECTOR DE PUNTO DECIMAL
• Utilizado para designar la posición del punto decimal para (+, 0, 2, 3, 4, 6, F) los resultados calculados.
• + (MODO SUMA)
Las adiciones y substracciones son realizadas con dos dígitos decimales automáticamente. Es conveniente para cálculos monetarios.
• F (PUNTO DECIMAL FLOTANTE) |
Todos los números efectivos hasta 12 dígitos son impresos o desplegados. |
BEFORE STARTING | ENGLISH |
•Remove the insulation tape and press the [RESET] button at the back of the calculator
before use. (Figure a )• Remove the tape on the ink ribbon of the calculator before use. (Figure b , c )
a | b | c |
INSTALLING PRINTING PAPER
1)Lift up the arm (Figure ).•When inserting the paper, cut the edge of the paper as shown.2)Place the new paper roll on the arm. The edge of the paper should be positioned as shown (Figure ).
•Suitable paper roll – Width: 57mm3)Insert the paper into the slit at the back of the machine as indicated. (Figure )
4)Turn the power switch on. Press the paper feed key to advance the paper as shown. (Figure )
REPLACING THE INK RIBBON
Note: Turn the power switch off.1)Lift up the tab on the
2)While pinching together the ribbon lock (A) in the direction of arrow, lift ribbon spools off the shafts. Discard the old ribbon and spools. (Figure )
3)Separate the spools of new ribbon between the tape and printer head. Guide it around the four positions of the ribbon guide (B) and place the spools on the shafts. (Figure )
4)When the ribbon spools have settled, release the ribbon locks. If necessary, rotate the spools until the pegs on the botton of the spool seat themselves in the holes of the spool holder. (Figure )
5)Rotate either spool to take up any ribbon slack, making sure that the ribbon is positioned around the four ribbon guides. Replace the printer cover. (Figure ) IMPORTANT: Use only the same type of ribbon spools.
REPLACING BACKUP BATTERY
Memory backup battery retains the tax rate, calendar and clock setting, even if the power is off or even when the AC cord is disconnected.
Battery : 1 Lithium battery (Type : CR2032)Battery life : Backup time 8 monthsCAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instruction.
ROUNDING SWITCH
ROUNDING • Used to
5/4
ITEM COUNT SWITCH
• At "n+" or
ITEM COUNTER
•When the "ITEM" switch is set at "n+", the calculator counts the number+and keys are pressed.•When the switch is set at+key is pressed and subtracts from the total number of timesof times thetimes the
the | key is pressed. |
MEMORY ITEM COUNT
•When the "ITEM" switch is set at "n+", the calculator counts number oftimes the and keys are pressed.•When the switch is set at
PRINTOUT OF ITEM COUNT
•When the "PRINT" switch is positioned at "ON", and the "ITEM" switch is at the "n+" or
GRAND TOTAL / RATE SET SWITCH
GRAND TOTAL |
|
|
|
|
| |||||||
|
|
|
|
|
| / | • | When the calculations are performed with the GT switch set to "ON", | ||||
OFF ON RATE SET |
| the totals are accumulated in the grand total memory. Each time |
| |||||||||
|
|
|
|
|
|
|
| is pressed, the subtotal number is printed with the symbol G+. When | ||||
|
|
|
|
|
|
|
| is pressed, the intermediate grand total is printed with the symbol | ||||
|
|
|
|
|
|
|
| G . Press | successively to get the grand total followed by the | |||
|
|
|
|
|
|
|
| symbol G |
| . |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
RATE SET
• Set switch to "RATE SET" for setting or recalling the TAX rate.OFF ON RATE SET
AUTO POWER SAVE
When the power is "ON" and the calculator is not being used for approx. 7 minutes,
the calculator will automatically switch to power save mode and the LED light will turn red. Press CEC to resume; the LED light will change back to green and the calculator will return to normal calculation mode.
OVERFLOW FUNCTION
In the following cases, when "E" is displayed, a "ERR" is printed, the keyboard is electronically locked, and further operation is impossible. Press CEC to clear the overflow. The overflow function occurs when:
1)The result or the memory content exceeds 12 digits to the left of the decimal point.
2)Dividing by “0”.3)The sequential operation speed is faster than the calculation processing speed. (Buffer Register Overflow)
Electromagnetic interference or electrostatic discharge may cause the display to malfunction or the contents of the memory to be lost or altered. Should this occur, use the tip of a ballpoint pen (or similar sharp object) to press the [ RESET ] button at the back of the calculator. After resetting, be sure to set the calendar, clock and tax rate again.
INSTALANDO PAPEL DE IMPRESIÓN
1)Levantar la cubierta de la impresora. (Figura )•Antes de introducir el papel, corte el borde del papel como se muestra.2)Coloque el nuevo rollo de papel en el brazo de la calculadora. El borde del papel deberá ser colocado como se muestra en la (Figura ).
•Rollo de papel adecuado – Ancho: 57mm3)Introduzca el papel en la ranura posterior de la máquina, como se indica en la. (Figura )
4)Encienda la calculadora. Presione la tecla de advance de papel para avanzar el papel como se muestra. (Figura )
COMO CAMBIAR LA CINTA
Nota: Apáguela.1)Levante la pestaña del lado posterior de la tapa de la impresora y luego retire la tapa. (Figura )
2)Mientras sostiene el seguro de la cinta (A) en la dirección de las flechas, levante los carretes de cinta del eje. Deseche la cinta y carretes viejos. (Figura )
3)Separe los carretes de cinta nueva entre la cinta y la cabeza de la impresora. Guíe la cinta alrededor de las cuatro guias de cinta (B) y coloque los carretes encima de los ejes. (Figura )
4)Permita que los carretes se asienten y suelte los seguros de cinta. Si es necesario, gire los carretes hasta que las clavijas en la base encajen en los huecos del soporte de carrete. (Figura )
5)Gire cualquiera de los carretes para templar la cinta y asegúrese que la cinta pase por las cuatro guias de cinta. Coloque nuevamente la cubierta de la impresora. (Figura )
NOTA IMPORTANTE: Utilice unicamente el mismo tipo de carretes de cinta y coloque la cinta de la manera indicada.
REEMPLAZO DE LA BATERÍA DE RESPALDO
La batería de seguridad de la memoria conserva la carga y el ajuste del calendario y del reloj cuando se interrumpe la alimentación o incluso cuando se desconecta el cable de CA.
Pila : 1 pila de litio (Type : CR2032)Duración de la pila : Tíempo de respaldo 8 mesesPRECAUCIÓN: Existe un riesgo de explosión si se utiliza un tipo de batería incorrecto. Siga las instrucciones para desechar las baterias.
Después de reemplazar la batería de respaldo, presione el botón [RESET]. Una vez restablecida, asegúrese de volver configurar el tipo impositivo y el de divisas.
SUMINISTRO ACTIVADO / DESACTIVADO
POWER
| CONMUTADOR DE REDONDEO | ||||||||||||
ROUNDING | • Es usado para redondear el resultado hacia arriba [ |
| ], redondear [5/4], | ||||||||||
| |||||||||||||
|
|
|
|
|
|
|
|
| o redondear hacia abajo [ |
| ] a la cantidad de decimales | ||
|
|
|
|
|
|
|
|
|
| ||||
|
| 5/4 |
|
|
| ||||||||
|
|
|
|
CONMUTADOR CONTADOR DE ENTRADAS
• Este conmutador activa la cuenta e impresión del número de artículos hasta 999.CONTADOR DE ENTRADAS
•Cuando el contador de n de entradas está situado en n+, la calculadora+y se presionan. Cuando el contador de entradas está situado en n+/– la calculadora contará el n de
+y restará del total el n de veces quese presiona la tecla .contará el n de veces que las teclasveces que se presiona la tecla
CONTADOR DE ENTRADAS DE MEMORIA
•Cuando el contador de n de entradas está situado en n+, la calculadora
contará el n de veces que las teclas y se presionan. Cuando el contador de entradas está situado en n+/– la calculadora contará el n de
veces que se presiona la tecla y restará del total el n de veces quese presiona la tecla .IMPRESIÓN DE LA CUENTA DE ARTICULOS
•Cuando el interruptor de impresión “PRINT” se posiciona en ON, y el interruptor de cuenta de entradas (ITEM) está en la posición n+ o
tecla para la cuenta de entradas y la tecla o la tecla para la memoria de cuenta de entradas.
INTERRUPTOR DEL GRAN TOTAL / IMPUESTOS AJUSTE DE TASA
GRAN TOTAL | • | Cuando los cálculos son realizados con el conmutador GT colocado | |||||||
| / | ||||||||
| |||||||||
|
|
|
| en Activado (ON), los totales son acumulados en el registro de gran | |||||
OFF ON RATE SET |
| ||||||||
| total. Cada vez que usted presiona |
| , el subtotal y el símbolo G+ | ||||||
|
|
|
|
| |||||
|
|
|
| son impresos. Cuando usted presiona la tecla | , el gran total | ||||
|
|
|
| intermedio es desplegado e impreso con el símbolo G . Presione | |||||
|
|
|
| por segunda vez para obtener el gran total seguido por el | |||||
|
|
|
| símbolo G |
| . |
|
|
|
|
|
|
|
|
|
|
| ||
IMPUESTOS AJUSTE DE TASA |
|
|
| ||||||
|
|
| • | Sitúe el interuptor en "RATE SET" Para fijarlo en el modo de | |||||
|
|
| |||||||
OFF ON RATE SET |
| conversión "TAX". |
|
|
| ||||
|
|
|
|
|
|
|
AUTO AHORRO DE ENERGIA
Cuando la energía es activada en “ON” y la calculadora no se usa por un periodo de aproximadamente 7 minutos, la calculadora cambiará al modo de ahorro de energía automáticamente y la luz LED cambiará a roja. Presione la tecla CEC y la calculadora se enccenderá otra vez LED cambiará a color verde para representar en modo normal.
FUNCIÓN DE REBOSE
En los siguientes casos, cuando aparece una "E" en la pantalla, una "ERR" es impresa, el teclado se bloquea electrónicamente, y la operación subsiguiente no es posible, presione CEC para borrar el rebose. La función de rebose ocurre cuando:
1)El resultado o el contenido de la memoria excede de 12 dígitos a la izquierda del punto decimal.
2)Divide por "0"3)La velocidad de la operación secuencial es más rápida que la velocidad del proceso de cálculo. (Rebosamiento del registro de la memoria intermedia)
Las interferencias eléctricas o la electricidad estática pueden ocasionar mal funcionamiento de la pantalla o la pérdida del contenido de la memoria. En caso de que esto se produzca, pulse la tecla [RESET], y reinicie el funcionamiento de su calculadora. Después de reiniciar, asegúrese de introducir
After replacing the
POWER ON/OFF SWITCH
POWER |
SPECIFICATIONS
Power Source: AC 120V, 60Hz, 0.2AOperation Temperature: 0ºC to 40ºC (32ºF to 104ºF)Calculating Capacity: 12 digits maximumOFF ON
POWER
OFF ON
ESPECIFICACIONES
Suministro de Energía: CA120V, 60Hz, 0.2ATemperatura de operación: 0ºC a 40ºC (32ºF a 104ºF)
|
|
| • The calculator is power on. | |
|
|
|
|
|
OFF | ON |
|
| |
POWER | • | The calculator is power off. | ||
|
|
| ||
OFF | ON |
|
|
PRINT ON/OFF SWITCH
OFF ON
OFF ON
Dimension: 358mm (L) x 227mm (W) x 86.4mm (H) /
The
For CA, USA Only
included battery contains perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for detail.
IMPRESIÓN / ENCENDIDO
OFF ON
OFF ON
Dimensiones: 358mm (longitud) x 227mm (ancho) x 86.4mm (alto) /
accesible. En caso de una falla eléctrica (p.e. humo), desenchufe la calculadora de la toma de corriente inmediatamente.
Para el Ca, los E.E.U.U. Solamente
La bataria includa contiene el material del perclorato - El manejo especial debe ser aplicado. Para el detalle, por lavor ver ://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for detail.