Operation Guide 4709 4713
To turn auto receive on and off
|
|
|
|
|
| 1. Press Bto display the Last Signal screen. | |
I | I I I I I | I | I | 2. Hold down A so the current auto receive setting (R/C | |||
on or R/C OF) is flashing. This is the setting screen. | |||||||
I |
|
|
|
| I | ||
I |
|
|
|
| I | • Though illumination will also turn on when you press | |
I |
|
|
|
| |||
|
|
|
| I | |||
I | I I I I | I | I | A, keep the button held down until R/C on or R/C OF | |||
|
|
|
| ||||
|
|
|
|
|
| flashes. | |
|
| On/Off status | • Note that the setting screen will not appear if the |
currently selected Home Time Zone is one that does not support time calibration reception.
3.Press Cto toggle auto receive on (on) and off (OF).
4.Press Ato exit the setting screen.
•For information about time zones that support signal receive, see “To specify your Home Time Zone”.
To check the latest signal reception results
Receive date | Press B to display the Last Signal screen. | |
• The display shows the time and date that receive was | ||
| ||
| successful. - | |
| operations were successful. | |
▲ | • To return to the Timekeeping Mode, press B. | |
|
▲
Receive time
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
Problem | Probable Cause | What you should do |
Cannot perform | • The watch is not in the Timekeeping | • Enter the Timekeeping Mode |
manual receive. | Mode. | and try again. |
| • Your current Home Time Zone is not one | • Select UTC +0, UTC +1, UTC |
| of the following: | +2, UTC +8, UTC +9, UTC |
| UTC +0, UTC +1, UTC +2, UTC +8, UTC |
|
| +9, UTC |
|
| UTC | ( DST ON : UTC +1, UTC +2, |
| ( DST ON : UTC +1, UTC +2, UTC +3, | UTC +3, UTC +9, UTC +10, |
| UTC +9, UTC +10, UTC | UTC |
| UTC | UTC |
|
| as your Home Time Zone. |
Time setting is | • If the time is one hour off, the DST | • Change the DST setting to |
incorrect | setting may be incorrect. | Auto DST. |
following signal | • The Home Time Zone setting is not correct | • Select the correct Home Time |
reception. | for the area where you are using the watch. | Zone. |
•For further information, see “Important!” under “Time Calibration Signal Reception” and
Dual Time
| The Dual Time Mode shows you the current time in 29 | |
| time zones around the world. | |
| • If the current time shown for a time zone is wrong, check | |
| your Home Time Zone time settings and make the | |
Current time | necessary changes. | |
• All of the operations in this section are performed in the | ||
in selected | ||
time zone | Dual Time Mode, which you enter by pressing B. |
To view the time in another Time Zone
1.In the Dual Time Mode, press Cto display the UTC differential value of the currently selected time zone for about two seconds.
2.To change the UTC differential value, press Cwhile a UTC differential value is on the display to scroll eastward through time zones.
•Note that if you do not press C to scroll within two seconds after displaying a UTC differential value, the display will change automatically to the current time based on the currently displayed UTC differential value.
3.When the UTC differential value you want is on the display, do not perform any button operation for about two seconds. This will cause the current time to appear, which will be based on the UTC differential value you selected.
To toggle a time zone time between Standard Time and Daylight Saving Time
1. In the Dual Time Mode, use C to display the time zone
DST indicator | whose Standard Time/Daylight Saving Time setting you |
| |
| want to change. |
| 2. Hold down Ato toggle Daylight Saving Time (DST |
| indicator displayed) and Standard Time (DST indicator |
| not displayed). |
• Turning on DST causes the UTC differential value to be increased by one.
• Though illumination will also turn on when you press A, keep the button held down until DST indicator displayed or DST indicator not displayed.
• The DST indicator will appear whenever you display a time zone for which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the currently displayed time zone. Other time zones are not affected.
• Note that you cannot switch between Standard Time and Daylight Saving Time while UTC is selected as the time zone.
• Note that you cannot use the Dual Time Mode to change the DST setting of the Home Time Zone you currently have selected in the Timekeeping Mode. See “To change the Daylight Saving Time (summer time) setting” for information about turning the Home Time Zone DST setting on and off.
Alarm
You can set a Daily Alarm. When an alarm is turned on, the alarm tone sounds when the alarm time is reached.
You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour.
•When you enter the Alarm Mode, the screen you were viewing when you last exited the mode appears first.
•All of the operations in this section are performed in the Alarm Mode, which you enter by pressing B.
•In the Alarm Mode, you can press Cto toggle the display contents as shown below.
Alarm screen | Hourly Time Signal screen |
Timekeeping |
|
Mode Seconds |
|
Alarm time | Hourly time signal on/off status |
(Hour: Minutes) |
To set an alarm time, and to turn Alarm on and off
|
|
| 1. In the Alarm Mode, use C to display the Alarm Screen. | |
II II | 2. Hold down Auntil the hour setting of the alarm time | |||
starts to flash, which indicates the setting screen. | ||||
I |
| I | ||
I |
| I | • Though illumination will also turn on when you press | |
I | I | |||
| II I |
| A, keep the button held down until the hour setting of | |
|
|
|
the alarm time flashes.
• This operation automatically turns on the alarm.
3. Press B to change the flashing contents in the sequence shown below to select other settings.
Hour |
| Minutes |
|
| Alarm On/Off |
| |||||
|
|
|
|
|
|
4. When the setting you want to change is flashing, use Cto change it as described below.
Screen: | To do this: |
|
| Do this: |
| Change the hour or minutes |
| Use C. | |
|
|
|
| |
| Toggle between alarm on ( | ), | Press C. | |
| and alarm off ( | ) |
|
|
•When setting the alarm time using the
5.Press Ato exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds.
Note
•Pressing any button stops the alarm tone operation.
To test the alarm
In the Alarm Mode, hold down Cto sound the alarm.
To turn the hourly time signal on and off
|
|
|
|
| 1. In the Alarm Mode, use Cto display the Hourly Time | |
I | I I I I I | I | I | Signal Screen. | ||
2. Hold down Auntil the hourly time signal on/off status | ||||||
I |
|
|
| I | ||
I |
|
|
| I | starts to flash, which indicates the setting screen. | |
I |
|
|
| |||
|
|
| I | |||
I | I I I I I | I | • Though illumination will also turn on when you press | |||
|
|
|
|
| A, keep the button held down until the hourly time | |
|
| On/off status | signal on/off status flashes. | |||
|
| • This operation automatically turns on the hourly time | ||||
|
|
|
|
| ||
|
|
|
|
| signal. | |
|
|
|
|
| 3. Press Cto toggle it on and off. | |
|
|
|
|
| 4. Press Ato exit the setting screen. |
Stopwatch
The stopwatch lets you measure elapsed time.
•The display range of the stopwatch is 59 minutes, 59.99 seconds.
•The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it.
Minutes | • The stopwatch measurement operation continues even | |||
| Seconds | if you exit the Stopwatch Mode. |
| |
| • All of the operations in this section are performed in the | |||
|
| |||
|
| Stopwatch Mode, which you enter by pressing B. | ||
Elapsed Time Measurement |
|
| ||
| • Up to one minute | • From one minute | ||
| Seconds | Timekeeping | Minutes | Timekeeping |
| Mode Seconds | Mode Seconds | ||
| 1/100 seconds | Seconds | ||
|
|
| ||
Elapsed Time Screen |
|
|
| |
| Minutes | Timekeeping |
|
|
| Mode Seconds |
|
| |
| Seconds | 1/100 seconds |
| |
|
|
| ||
To measure times with the stopwatch |
|
| ||
Elapsed Time |
|
|
| |
C | ➤C | ➤C | ➤C | ➤Hold downC |
Start | Stop |
| Stop | Clear |
Illumination
An LED
•See “Illumination Precautions” for other important information.
To turn on illumination
• In any mode (except when a setting screen is on the display), press A to illuminate the digital display.
• When turning on illumination, press Aand immediately release it. If you keep A held down too long, either of the operations described below will be peformed.
If you hold down Awhile in the Timekeeping Mode, Alarm Mode, or Hand
Setting Mode
The figures on the display will start to flash, which indicates the setting screen. If this happens, press Aagain to exit the setting screen.
If you hold down Awhile in the Dual Time Mode
The DST setting will toggle between Standard Time and Daylight Saving Time, which will affect the current time setting.
If this happens, hold down Aagain to toggle setting back to its original setting (if necessary).
3