®
INSTALLATION
1.Open your garage door and park your vehicle outside of garage.
2.Determine the mounting location on the ceiling and fasten the parking assist using screw and anchor (Figure 1).
3.Depress tabs under the wires and temporarily remove the white and white/black safety sensor wires from the garage door opener.
4.Stripping the wires prior to installation:
Installing one parking assist: Separate white and white/black wires and strip 7/16" (11 mm) of insulation from parking assist wires.
Installing two parking assists: Cut 6" (15 cm) of wires from the end of one set of parking assist wires for use as connection wires. Separate white and white/black wires and strip 7/16"
(11 mm) of insulation from both ends of connection wire.
5.Connecting the wires to garage door opener: Installing one parking assist: Twist like colored wires for parking assist and safety sensors together. Insert twisted wires into
Installing two parking assists: Separate white and white/black wires and strip 7/16" (11 mm) of insulation from the end of parking assist wires. Twist like colored wires for parking assists, safety sensors and connection wire together. Secure with wire nut. Insert connection wires into
*Please refer to your garage door opener owner’s manual for proper wire installation.
SET UP AND ADJUSTMENT
1.Drive your vehicle into garage and park in the desired location.
2.Activate the parking assist by obstructing the path of the safety sensors. The laser will emit a pulsing bright red beam (Figure 4). Aim the red beam to a location on the dash or hood that can easily be seen while seated in the driver’s seat.
NOTE: The laser will shut off in 1 minute. If you are not finished adjusting the beam and it turns off, simply obstruct the path of the safety sensors.
3.Sit in the driver’s seat and confirm that you can easily see the location of the red beam. This location is now your point of reference for parking your vehicle.CAUTION: Do not stare directly into the beam. Repeat steps for installation on optional 2nd laser accessory kit.
NOTE: Periodic adjustment of the beam may be required.
OPERATION
1.Open the garage door by activating the garage door opener and drive your vehicle into parking space.
2.The red beam can be seen moving across the hood of your vehicle as you drive further into the garage (Figure 4).
3.Stop the vehicle when the beam is positioned at the location you confirmed in step 3 during SET UP AND ADJUSTMENT.
NOTE: The laser is activated every time you drive into your garage. The laser will shut off in 1 minute. A residual reflection of the red beam from the windshield may appear on walls or objects in your garage. When operating a vehicle, always ensure that there are no objects on the floor of the garage or in the path of your vehicle. The parking assist is not a substitute for safe parking practices.
TROUBLESHOOTING
If the laser does not emit a beam:
•Verify nothing is obstructing the safety sensors.
•Verify nothing is blocking the parking assist lens.
•Verify that connections are not reversed.
•Verify that all connections are secure.
•Confirm that the parking assist is aimed toward the garage floor.
•Obstruct the path of the safety sensors and look for the red spot on the garage floor.
Please refer to your owner’s manual for additional information on your garage door opener and the safety sensors.
Models CLLP1 and CLLP1C Chamberlain Laser Garage Parking Assist
Owner’s Manual
CAUTION
To avoid eye INJURY or damage to product:
•NEVER point the laser at anyone.
•NEVER look directly into the laser beam.
•NEVER disassemble the laser.
•The parking assist is NOT a substitute for safe parking practices.
•Use of controls or adjustments, or the performance or procedures other than specified can result in hazardous radiation exposure.
•ONLY for use on Chamberlain manufactured garage door openers.
CAUTION
ATTENTION
LASER RADIATION
DO NOT STARE INTO BEAM
RAYONNEMENT LASER
NE PAS REGARDER DIRECTEMENT
LE RAYONNEMENT LASER
Maximum power output: < 1mW @ 635 - 670nm |
|
Puissance de sortie maximum: < 1mW @ 635 - 670nm | |
APPAREIL AU LASER DE CLASSE II | 132C2469 |
CLASS II LASER PRODUCT |
|
This Class B digital apparatus complies with
CARTON INVENTORY
Anchor
Screw | Wire Nut | Parking Assist |
Figure 1
Figure 2 |
|
| Insert Into Appropriate Terminals | |
Safety Sensor | Parking Assist |
|
|
|
Wires |
|
|
| |
Wires |
|
|
| |
|
|
|
| |
|
|
|
| Red White Grey |
Figure 3 | Wire Nut | Insert Into Appropriate Terminals | ||
White |
|
| ||
|
| White/Black | ||
|
| Connection | ||
| Connection | Connection | ||
Safety | Wire |
| ||
Wire |
| Wire | ||
Sensor |
|
| ||
|
|
|
| |
Wires |
|
|
|
|
| Parking Assist |
|
|
|
| Wires |
|
|
|
|
|
| Red White Grey | |
Figure 4 |
|
|
| Parking Assist |
|
|
|
| |