USER INSTRUCTIONS
The Security✚® remote control works only with door openers and light controls having an orange “Learn” button and yellow indicator light.
Programming instructions are described and illustrated below. The additional push buttons can also activate other garage door openers and/or light controls. (Instructions for programming light products are included with
those accessories.)
Remote Coding Instructions
OR 
1 2
1. Press and release the “learn” button on the motor unit. The learn indicator light will glow steadily for 30 seconds.
2. Within 30 seconds, press and hold the button on the
3.Release the button when the motor unit light blinks. It has learned the code. If light bulbs are not installed, two clicks will be heard.
Model 139.53681B
Security✚® 3-Function Remote Control
Model 139.53680
Security✚® Compact 3-Function Remote Control
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
•ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
•Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
•ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
To Control the Motor Unit Lights (Premium Consoles Only)
With Security✚® transmitters, a remote push button can be programmed to operate the motor unit lights without opening the door.
1.With the door closed, press and hold the remote button that you want to control the light.
2.Press and hold the Light button on the door control.
3.Press and hold the Lock button on the door control.
4.After the motor unit lights flash, release all buttons.
Test by pressing the remote push button. The motor unit lights should turn on or off but the door should not move.
The Remote Control Batteries
WARNING
To prevent possible SERIOUS INJURY or DEATH:
•NEVER allow small children near batteries.
•If battery is swallowed, immediately notify doctor.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes.
Press and hold the “learn” button on motor
unit until the “learn” indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use.
The lithium battery should produce power for up to 5 years. To replace battery, use the visor clip or screwdriver blade to pry open the case as shown. Insert battery matching polarity instructions inside the remote cover or on the printed cirucuit board.
Dispose of old battery properly.
COMPACT 
Twist here
to open
Security✚®
housing only (No circuit board) . . . . . . . . . . . . . .41A5032 Security✚® Compact
housing only (No circuit board) . . . . . . . . . . . . . .41A5062
3V2032 Lithium battery:
(Models 139.53681B and 139.53680) . . . . . . . . . . .10A20 3V2016 Lithium battery: (Model 139.53681) . . . . . .10A19 Visor clip: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B134
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
To order replacement parts call...© 2006, Sears, Roebuck and Co./ ® Registered Trademark / ™ Trademark / SM Service Mark of Sears, Roebuck and Co.
®Marca Registrada / ™Marca de Fábrica / SM Marca de Servicio de Sears, Roebuck and Co.
114A2110D