Figure 4
Figure 3

®

Model 139.53684

 

Keyless Entry

Features
For use with any SECURITY✚ compatible
garage door opener receiver.

Personalized Password: Up to 10,000 possible combinations. Password can be easily changed if desired.

Temporary password: Can be added for visitors or service

persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries.

Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes.

Operation: Opener activates when 4-digit password and Enter button is pressed.

To comply with FCC rules, adjustment or modification of receiver and/or transmitter is prohibited, except for changing the password setting and replacing the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

WARNING

Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the wall push button(s) or remote control(s).

A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door clearly, it is free of obstructions, and is properly adjusted.

If wrong numbers are accidentally pressed, correction can be made immediately. The Enter button will transmit only the last four digits.

The Keypad will blink for 15 seconds after the password is transmitted. During that time the Enter button can be used to stop or reverse the door travel.

The Lock feature on openers with premium door controls is designed to prevent operation of the door from portable transmitters. However, the door will open and close from the door control push button and the Keyless Entry.

Setting the Personal Entry Password
We recommend that you program your password now, before
Installation

The recommended mounting locations for sectional and one-piece doors are shown in Figure 3. You can select another location if you prefer. However, the

keypad must be installed within sight of the door.
Keypad
Exterior Front Wall 1-Piece or Sectional Door

Door Jamb Edge (Optional Location for 1-Piece Door)

Door Jamb Face
SECTIONAL DOOR ONLY

KEYPAD MUST BE INSTALLED WITHIN SIGHT OF THE DOOR

you install the Keyless Entry. Then you can test the reception at the mounting location before you proceed further.

Choose a 4-digit password using the numbers from 0 to 9 (a number can be used more than once, for example, 4,0, 4,1.)

For a one-piece door,
use the optional location shown in the

illustration (on the edge of the door jamb) to avoid injury as the door swings up and out.

Test the reception of the Keyless Entry by operating your
If you have a Premium Control Console:

1.

With the door closed, press the four buttons for

 

the password, then press and hold Enter.

2.

Press and hold the light button on the door

 

control, Figure 1.

3.

Press and hold the door control push button.

Door Control Push button

LIGHT

LOCK

opener from the selected location. Change the location if necessary.
Open the keypad and remove the

Keypad

battery compartment screw and
Cover

 

cover to access the bottom

 

mounting hole (Figure 4).

 

 

4. After the opener light flashes, release all
buttons.
If you do not have a Premium Control Console:
Light

Figure 1

Center the keypad at eye level against the selected location. Mark 4 1/4" up the centerline from the bottom and drill a 1/8" pilot hole.

Bottom mounting hole

1.

Enter the four digit password desired, then press and hold

 

Enter.

2.

Press and release the SRT (learn) button on the door

 

opener panel, Figure 2.

Install top mounting screw, allowing 1/8" to protrude above surface. Position keypad on screw head and adjust for snug fit.

Battery

Battery

Cover

3. After the opener light flashes, release the Enter button.

Test by pressing your password, then press Enter. The door should begin to move.

This procedure can be repeated with a different password for use with a second garage door opener.

Figure 2

✯❒❁■❇❅

✑

✒

 

 

✓

 

 

 

✳✲✴ ✈●❅❁❒■✉

 

 

 

 

Security✚

✢◆▼▼❏■

 

 

 

 

 

✹❅●●❏◗

 

✙

✑

✙

✑

Garage Door Opener

✩■❄❉❃❁▼❏❒

✗

✓

✗

✓

 

 

 

✕

 

 

✕

 

✬❉❇❈▼

 

✫✧

 

 

✫✧

 

 

 

 

 

 

With cover open so bottom
mounting hole is visible, use a punch to

mark hole. Remove keypad and drill 1/8" pilot hole. Replace keypad and complete installation with bottom screw, using care to avoid cracking plastic housing. Do not overtighten.

Replace the battery cover.

Side two contains instructions for changing the personal entry password and setting a temporary password.

1