ENGLISH

Easy Setup Procedure

iChecking and storing the measurement results

The measurement results displayed at “u Speaker measurements” can be checked and stored in the memory.

1 Press D H to select the item, then press ENTER.

Press ENTER to switch to the second screen.

2 Afterset. checking, press ENTER, then press D H to

Store:

All the settings are stored in the memory.

Cancel:

Cancel the auto setup settings.

3 When “Store” is selected: Press F.

• After the data is stored, the “Auto Setup / Room EQ” screen appears automatically.

1

2

Easy Setup Procedure

Error messages

An error message is displayed if the measurements could not be completed automatically due to the speaker layout, the measuring environment, etc. Please check the following matters, reset the pertinent items, and measure again.

Be sure to turn off the AVR-2807’s power before checking the speaker connections.

 

 

 

Example

 

Cause

Measures

 

 

 

 

 

 

 

 

 

 

 

 

 

q The speakers required for producing suitable

• Check that the pertinent speakers are properly

 

 

 

 

 

 

 

 

 

 

 

 

 

reproduction have not been detected.

connected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If multiple errors occur, press F G to check the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

contents.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

w The speaker polarity is connected in reverse.

• Check the polarity of the pertinent speakers.

 

 

 

 

 

 

 

 

 

 

 

 

 

If multiple errors

occur, press F G to check the

• For some speakers, the screen below may be

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

displayed even though the speakers are

 

 

 

 

 

 

 

 

 

 

 

 

 

contents.

 

properly connected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If so, select “Skip0”.

eThere is too much ambient noise in the room and the • Either turn off the power of the device that

measurements cannot be made accurately.

generated the noise during the measurements

 

or move the device away.

 

• Try again at a time when it is quieter.

r The sound level that is output from the speakers and/or

• Check the placement and orientation of the

subwoofer is too low.

loudspeakers.

 

• Adjust the subwoofer’s output level.

t The measurement microphone is not connected, or all

• Connect the

attached setup microphone to

of speakers have not been detected.

<SETUP MIC>.

 

 

• Check the speaker connection.

•When measurements have been made using the measurement microphone, speakers with a built-in filter such as subwoofers might be set with a value that differs from the physical distance because of the internal electrical delay.

NOTE:

• Do not turn off the power while the data is being stored.

12

ENGLISH