Denon AVR-3805 manual

CH SEL

ENTER

AV SURROUND RECEIVER

AVR-3805

OPERATING INSTRUCTIONS

2We greatly appreciate your purchase of the AVR-3805.

2To be sure you take maximum advantage of all the features the AVR-3805 has to offer, read these instructions

carefully and use the set properly. Be sure to keep this manual for future reference, should any questions or

problems arise.

“SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE

CABINET FOR FUTURE REFERENCE”

Contents

Main AV SURROUND RECEIVER AVR-3805 OPERATING INSTRUCTIONS 2SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: CAUTION ATTENTION SAFETY INSTRUCTIONS 2INTRODUCTION 2ACCESSORIES TABLE OF CONTENTS 2 CAUTIONS ON INSTALLATION BEFORE USING 3CAUTIONS ON HANDLING 4FEATURES Page 5CONNECTIONS Connecting the audio components Connecting the pre-out jacks Connecting the AC OUTLETS AC CORD Connecting the video components Connecting the video components equipped with S-Video jacks The Video Conversion Function Connecting the antenna terminals An F-type FM antenna cable plug can be connected directly. Connecting the external input (EXT. IN) jacks For instructions on playback using the external input (EXT. IN) jacks. (See page 63) Connecting the MULTI ZONE jacks Connecting the video component equipped with V. AUX jacks To connect the video signal, connect using a 75 /ohms video signal cable cord. LINE OUT VIDEO OUT LINE OUT DIGITAL OUT 1 2DENON LINK Setting 2 2Playback using the DENON Link connector (L) ( Speaker system connections Protector circuit Note on speaker impedance Page Display ert y!6uio!0!1!2!3!4!5 qw Remote control unit For details on the functions of these parts, refer to the pages given in parentheses ( ). 7SETTING UP THE SYSTEM System setup items and default values (set upon shipment from the factory) SYSTEM SETUP button Press this to display the system setup menu. 1 Use the following buttons to set up the system Use the following buttons to set up the system. 2. Speaker Setup 4 3.Input Setup 4.Advanced Playback 5.Option Setup 5 7 Before setting up the system Auto setup/Room EQ Setting the Auto Setup / Room EQ 2 1 Connecting the microphone for Auto Setup 1-1 Setting the Auto Setup 3 1 4 2 5 1 2 About automatic retry About the error message Check of the measurement results 1 2 3 1-2 Setting the Manual EQ Setup 1 2 5 3 4 1 3 5 1-4 Setting the Direct Mode 1 Room EQ Menu. Perform the ON/OFF setting of Room EQ when the surround mode is Direct or Pure Direct. 2 3 1 2 3 1-6 Check the EQ parameter 1 2 Setting the Speaker Setup Select Speaker Setup at the System Setup Menu . Display the Speaker Setup Menu screen. 6 select Exit and press the ENTER button. The Auto Setup Menu reappears. 7 3 4Display the parameter screen. 5 2-1 Setting the type of speakers 2-2 Setting the Delay Time 1 6 7 2-3 Setting the Channel Level Page 8 2-4 Setting the crossover frequency 1 2 2-5 Setting the low frequency distribution 1 2 2-6 Selecting the Surround Speakers for the different surround modes 3 Setting the Input Setup 1 2 1 3-1 Setting the Digital In Assignment 3-2 Setting the Ext. In Subwoofer Level 1 2 3-3 Setting the Component In Assign 1 2 3-4 Setting the Video Input Mode 3 3-5 Auto Tuner Presets 1 2 3 Setting the Advanced Playback 1 2 4-1 Setting the Audio Delay 4-2 Setting the Dolby Digital Setup 1 3 4-3 Setting the Auto Surround Mode 1 3 Setting the Option Setup 1 2 1 3 5-1 Setting the Power Amplifier Assignment 2 1 5-2 Setting the Zone2 vol. Level 3 5-3, 5-4 Setting the Trigger Out Setup 5-6 Setting the On Screen Display (OSD) 1 2 3 5-5 Setting the Muting Level 1 3 4 5 5-7 Protecting the setting 1 2 3 4 After completing system setup 1 This button can be pressed at any time during the system setup process to complete the process. 8REMOTE CONTROL UNIT Inserting the batteries Using the remote control unit Operating DENON audio components 2 3 Page Preset memory 5 2, 4 Operating a component stored in the preset memory Press the mode selector button for the component you want to operate. Page Learning function 1 2 8 7 6 Page 1 Punch Through 3 4 3, 4 Setting the back lights lighting time 3 2, 3 Setting the brightness Up Down Enter Page Page 9OPERATION 1 Operating the remote control unit 4 Before operating 2 1 2 3 4 5 Playback using the external input (EXT. IN) jacks 1 2 Playing audio sources (CDs and DVDs) 1 2 4 3 312 1 1 111 231 2 1 3 1 2 1 Multi-source recording/playback 3 4 2, 4 1, 2 10 MULTI ZONE Multi-zone playback with multi-source * MULTI ROOM MUSIC ENTERTAINMENT SYSTEM MAIN ZONE 7.1-channel systems ZONE 2 ZONE 3 * MAIN ZONE 5.1-channel systems ZONE 2 ZONE 3 MAIN ZONE 5.1-channel systems ZONE 2 ZONE 3 1 3 2 1 5 4 1 2 3 1 2 Fader function 1 2 Dolby Pro Logic IIx (Pro Logic II) mode 1 2 134~6 1 3 4, 5, 6 4 5 7 6 3 1 2 134~6 1 3 4, 5, 6 3 4 5 6 2 5, 6 4 4 5 Checking the input signal Adjusting the Audio Delay 3 2 4 8 3, 5, 7 2, 9 11 4, 6, 8 12 DSP SURROUND SIMULATION Surround modes and their features DSP surround simulation 1 12, 4 2 4 2,4 1 6 7 6 1, 7 2~5 1 button is pressed. 2 BASS Surround parameters e Parameter (default values are shown in parentheses) When playing Dolby Digital and DTS signals 13 LISTENING TO THE RADIO 1 3 4 3 4 1 Checking the preset stations 2, 5 2 3 5 1 1, 2 2 14 LAST FUNCTION MEMORY 3 2 1 15 INITIALIZATION OF THE MICROPROCESSOR 1 2 16 TROUBLESHOOTING 17 ADDITIONAL INFORMATION Optimum surround sound for different sources Surround back speakers Speaker setting examples 2. When not using surround back speakers Surround DTS Digital Surround DTS-ES Extended Surround DTS 96/24 HDCD (High Definition Compatible Digital) DENON LINK (DENON Digital Link) AL24 Plus (AL24 Processing Plus) System setup items and default values (set upon shipment from the factory) 1. Speaker Setup 3.Advanced Playback 2.Input Setup 4 Surround modes and parameters 7 3 Channel output Parameter (default values are shown in parentheses) When playing Dolby Digital and DTS signals Surround Mode Input signals 2Differences in surround mode names depending on the input signals 18 SPECIFICATIONS *