Denon AVR-4311CI nnAudyssey Settings

nnAudyssey Settings Default settings are underlined.

Set MultEQ® XT 32, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto Setup has been performed. For additional information on Audyssey technology, please see page 132.

NOTE

If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.

In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 12) to return to the settings after Audyssey Auto Setup was run.

Setting items	Setting details
MultEQ XT 32	OFF : Turn “MultEQ XT 32” equalizer off.
Select one equalizer from	Audyssey : Optimize the frequency response of all speakers.

three modes. MultEQ XT 32 Audyssey Byp.L/R : Optimize frequency response of speakers except

corrects both time and	front L and R speakers.
frequency response	Audyssey Flat : Optimize frequency response of all speakers to flat
problems in the listening	response.
area based on Audyssey	Manual : Apply frequency response set with “Manual EQ” (vpage 91).
Auto Setup calibration. We
recommend “Audyssey”.	• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
MultEQ XT 32 is the
	selected after Audyssey Auto Setup has been performed. “Audyssey”
prerequisite function for
	is automatically selected after performing Audyssey Auto Setup. When
Dynamic EQ and Dynamic
	“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
Volume.
	illuminates.

• After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without increasing the number of speakers

measured, only illuminates.

• Pressing MULTEQ makes this setting.

NOTE

•“MultEQ XT 32” and “Manual” cannot be selected when “EQ Customize” is set to “Not Used” (vpage 100).

•When using headphones, “MultEQ XT 32” is automatically set to “OFF”.

“MultEQ XT 32”, “Dynamic EQ” and “Dynamic Volume” settings are stored for each input source.

AUDIO/VIDEO ADJUST

Setting items				Setting details
Dynamic EQ	ON : Use Dynamic EQ.
Solve the problem of	OFF : Do not use Dynamic EQ.
deteriorating sound quality
as volume is decreased	•	or	is displayed when set to “ON”.
by taking into account
human perception and	• Buttons on the remote control unit or main unit
room acoustics. Works with
MultEQ XT 32.		can be used for operations.
		Press DYN EQ/VOL.
		Each time DYN EQ/VOL is pressed, the setting is
		changed as shown below.
			Dynamic EQ : ON		Dynamic EQ : ON
			Dynamic Volume : Midnight		Dynamic Volume : Evening
		Dynamic EQ : OFF		Dynamic EQ : ON		Dynamic EQ : ON
		Dynamic Volume : OFF		Dynamic Volume : OFF		Dynamic Volume : Day
Reference Level Offset	0dB (Film Ref) : This is the default setting and should be used when
Audyssey Dynamic EQ is	listening to movies.
referenced to the standard	5dB : Select this setting for content that has a very wide dynamic range,
film mix level. It makes	such as classical music.
adjustments to maintain	10dB : Select this setting for jazz or other music that has a wider dynamic
the reference response	range. This setting should also be selected for TV content as that is usually
and surround envelopment	mixed at 10 dB below film reference.
when the volume is turned	15dB : Select this setting for pop/rock music or other program material
down from 0 dB. However,	that is mixed at very high listening levels and has a compressed dynamic
film reference level is not	range.

always used in music or	Setting is enabled when “Dynamic EQ” is “ON” (vpage 89).
other non-film content.
Dynamic EQ Reference
Level Offset provides three
offsets from the film level
reference (5 dB, 10 dB, and
15 dB) that can be selected
when the mix level of the
content is not within the
standard.

version Simple

version Basic

version Advanced

Information

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu	89
buttons	(Up/Down/Left/Right)