12
ENGLISH
Sampler playback
8SAMPLER
1Select the source of Sampler
•Turn the ASSIGN switch yin the SAMPLER
part to select the desired source.
3
Setting B point / Stop recording
When the B button ois pushed during
recording, the B point is set.
•Recording continues for approximately 8
seconds without stopping after set B point.
•If the B point is not set, recording end point
set as B point automatically.
2
Record in Sampler
When the A button iis pushed, the sound of
the selected source is recorded to Sampler
memory up to 8 seconds.
•The A button iflashes after recording starts.
•When the recording is completed, B button
olights up.
5-1
Select Sampler play mode
You can select play mode for Sampler when
Sampler playback stop.
Loop (default):
Sampler playback continues with looping.
Single:
Sampler playback stops at B point.
Stutter:
Sampler is played while the A button iis
pressed and held down.
Loop + Reverse:
Reverse Sampler playback continues with
looping.
Single + Reverse:
Reverse Sampler stops at A point.
Stutter + Reverse:
Reverse Sampler is played while the A
button iis pressed and held down.
Exit B:
Sampler playback continues over B point
up to recording length.
6
Play Sampler sound
•Playback of the Sampler sound starts when
the A button iis pushed after recording has
completed.
•To stop the Sampler sound, push the
MODE/STOP knob u.
•When the CROSSFADER ASSIGN switch !0
in the SAMPLER part is set A or B, you can
perform the Sampler Fader Start by the
Crossfader !8. See page 10.
7
Moving Sampler B point
•When the B button ois pushed during
Sampler playback, the B point moves to the
point at which the button was pushed, and
Loop playback from point A starts.
4
Setting the Sampler sound level
The sound level (volume) can be set for
Sampler.
•To select “S_Level” turn the MODE/STOP
knob uand push.
•Turn the MODE/STOP knob uand select
between “–14 dB” and “+6 dB”.
9Clearing the Sampler data
•While pressing the MODE/STOP knob u,
push the A button ito clear the Sampler.
Sampler A/B Trim
1Select A-B Trim mode
•To select “A/BTrim” turn the MODE/STOP
knob uand push.
2
Select A point (in A-B Trim)
•Push the A button i.
•The A button iillumination flashes and Loop
playback starts.
5
Select B point (in A-B Trim)
•Select the A-B Trim mode and push the B
button o.
•The B button oillumination flashes.
3Trim A point
•Turn the MODE/STOP knob u. You can move
the A point.
4Save the A point
•Push the MODE/STOP knob uto save new
the A point.
6Trim B point
•Turn the MODE/STOP knob u. You can move
the B point.
9PFL (Pre Fader Level)
1. Press the SPLIT CUE button @4.
2. Press the CUE button !6 that you wish to monitor
1~ 4 (make sure your source is playing).
3. Turn the GAIN control #5 until the meters peak at
the 0 dB level.
4. Perform your mix using the Crossfader !8 or Ch.
Fader !9 at your desire.
NOTES:
•For proper operation, your channel levels should
always be set to or left on reference line 8.
•This adjustment can be made even if the Ch. Fader
is set to zero level.
Setting the Sampler pitch
The sound pitch can be set for Sampler.
•To select “S_Pitch” turn the MODE/STOP
knob uand push.
•Turn the MODE/STOP knob uand select
between “–100 %” and “+100 %”.
8
To select Loop/Reverse mode, turn the
MODE/STOP knob uthen push after
recording and before playing.
qPlay mode:
•To select “P_Mode” turn the
MODE/STOP knob uand push.
•Turn the MODE/STOP knob uand select
“Loop”, “Exit B”, “Single” or “Stutter”.
wPlay direction:
•To select “DirMode” turn the
MODE/STOP knob uand push.
•Turn the MODE/STOP knob uand select
“Forward” or “Reverse”.
5-2
10
Monitoring the Sampler data
(SAMPLER CUE)
•When the SAMPLER CUE button !6 is
pressed, you can check the Sampler data.
NOTE:
When the SAMPLER CUE button is lit, the
Sampler sound is not output into the
Crossfader or MASTER OUT.
7Save the B point
•Push the MODE/STOP knob uto save new
the B point.