26" LCD TV
QUICK SETUP GUIDE
DX-26L150A11
| Remote control | AC power cord | Component |
| and |
| video cable |
| 2 AAA batteries |
|
|
TV stand and screws
Quick Setup Guide
Front and side features
+
-
Remote control | Power |
| sensor | indicator |
Installing the stand
1Remove the stand from the box and place it on a table or bench.Note: Pay close attention to the direction of the stand. The wide portion of the stand must face the front of the TV.
2Lay the TV on a flat, cushioned surface.3 Align the stand with the TV, as shown.4 Move the stand gently (A) until the locators on the stand column align with the locating grooves on the stand (B).
|
|
|
|
|
|
| A |
|
|
|
|
|
|
|
|
| B |
|
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||
|
|
|
| |||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
C
6Secure the stand to the column with the four screws providedLocating groovesInstalling a wall-mount bracket
1Carefully place your TV screen
2Remove the four screws holding the TV to its stand column, then remove the stand column.
3Secure the
Setting up your remote control
1While pressing the release button on the battery compartment cover on the back of the remote, lift the cover off the remote.
2Insert two AAA batteries into the battery compartment. Make sure that the + and – symbols on the batteries align with the + and – symbols in the battery compartment.
3Replace the cover.To program your existing remote control to work with your Dynex TV, see the table below for common codes. If you have problems programming your remote, or need a different remote control code, visit www.dynexproducts.com for the latest remote control code information.
Universal remote control TV codes (for all Dynex TVs manufactured after Jan. 1, 2007)
Universal remote control makers and models |
|
| |||||||
Philips | RCA | One for All | Sony | Comcast | Dish Network | Motorola | TIVO | DirectTV | |
PHDVD5, PH5DSS, | |||||||||
RCU807 | M1057 | VIP508, VIP622 | DRC800 | Series 3, HD | RC23 | ||||
PMDVR8, PDVR8 | |||||||||
|
|
|
|
|
|
|
| ||
115 | 135 | 0464 | 8043 | 0463 | 720 | 0463 | 0091 | 10463 | |
|
|
|
|
|
|
|
|
| |
Connecting a DVD or
Using HDMI (best)
Back of TV
HDMI device
HDMI cable (not included)
Using component (better)
Back of TV
Component video device
Component video cable
Using composite (good)
Back of TV
Video device
N
Composite video cable
Using S-video (fair)
Back of TV
Video device
N
Connecting an antenna
Connect a 75 ohm cable (not included) to ANT/CABLE IN jack on the back of your TV and the RF OUT jack on the antenna.
Back of TV
Antenna cable
Connecting a home theater system
Using analog audio cable:
Back of TV
Audio cable
Note: Cable connectors and jacks are often
Using digital audio cable:
Back of TV
Note: The DIGITAL OUTPUT jack only works with digital TV channels.