6 Select the Wired LAN menu and press .
7 Choose IP Settings and press .

8

If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.

9

To prevent the IP address from appearing on the network standby screen,
set the SSID Display and/or IP Address Display settings to Off.

10

When you are finished, select Complete and press , then press
again to save your settings.
11 Press the Menu button to exit the menu system.
12 See “Install network software” for additional instructions.
Install network software
Install the EasyMP® Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, click the icon
on your desktop to access the online EasyMP Network Projection Operation
Guide (requires an Internet connection). If you don’t see the EasyMP Network
Projection Guide icon, you can install it from the projector CD or go to the
Epson website, as described on the right.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install a link to the downloads page from the projector CD or go to the
Epson website, as described on the right.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
• Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
• Press the Source Search button on the projector or the remote control to
select the computer as the image source.
• If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as . You may have to hold down the
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
• If you’re using a Mac® laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary, then
click the Arrange or Arrangement tab, and select the Mirror Displays
check box.
4 Replace the cable cover and tighten the screws.
5 Plug in and turn on the projector.
6 To configure your projector for your wireless network, do one of
the following:
• If you’re using the optional Quick Wireless Connection USB key
(Windows only), insert it into the projector’s USB TypeA port, wait
for the displayed message, remove the key, and connect it to a USB
port on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the online
User’s Guide.
• If you’re not using the key, continue with these steps.
7 Press the Menu button on the remote control, select the Network
menu, and press .
8 Choose Network Configuration and press .
9 Select the Basic menu and press .
10 Select the Projector Name setting, press , and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
11 Select the Wireless LAN menu and press .
12 Select the Connection Mode setting, press , and choose one of
these options:
• Quick to connect the projector to one computer on the network
• Advanced to connect the projector to multiple computers on
the network
13 If you selected Quick connection mode, select the Channel setting for
your wireless network and turn on the SSID Auto Setting setting.
Epson and EasyMP are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko
Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2011 Epson America, Inc. 11/11
Printed in XXXXXX CPD-35669
14 Select the type of wireless network you are using as the Wireless LAN
Sys. setting.
15 If you selected Advanced connection mode, enter your network SSID (up
to 32 characters) as the SSID setting.
16 If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
17 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display settings
to Off.
18 When you are finished, select Complete and press , then press
again to save your settings.
19 Press the Menu button to exit the menu system.
20 See “Install network software” for additional instructions.
Project over a wired network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1 Plug in and turn on the projector.

2

Press the Menu button on the remote control, select the Network menu,
and press .
3 Select Network Configuration and press .
4 Select the Basic menu and press .

5

Select the Projector Name setting, press , and enter a name (up to
16 characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
Where to get help
Manuals
For more information about using the projector, click the icons on your
desktop to access the online manuals (requires an Internet connection). If you
don’t have icons to the manuals, you can install them from the projector CD or
go to the Epson website, as described below.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 am to 6 pm, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
US: (562) 276-4394, 6 am to 8 pm, Pacific Time, Monday through Friday, and
7 am to 4 pm, Pacific Time, Saturday
Canada: (905) 709-3839, 6 am to 8 pm, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).