Manuals / Brands / Household Appliance / Humidifier / Fisher & Paykel / Household Appliance / Humidifier

Fisher & Paykel MR810 6.6REPLACING THE POWER CABLE OR HEATER-WIRE ADAPTOR, Supply, Power Cable, Phase, Neutral, Earth, Plug, Voltage, Colour

1 43

Download 43 pages, 1.11 Mb

6.5.7INSTALLING THE HEATER PLATE

Heater plate spring

		Figure 6.9: Heater plate assembly
	1.	Ensure the heater plate springs are located in their respective location holes on the heater plate.	6
	2.	Pull the heater plate harness through the hole in the case top (Figure 13).	6
	2.

3.Carefully orient the case upper over the heater plate springs, then screw the three mounting screws back into place.

6.6REPLACING THE POWER CABLE OR HEATER-WIRE ADAPTOR

Note: The spare heater-wire adaptor, part number 043 042 322, includes the cable clamp and collet for the mains cable and heater-wire adaptor.

Table 10: Part numbers and colour codes of Fisher & PaykelHealthcare power cables

Model	Supply	Power Cable	Phase	Neutral	Earth		Plug
	Voltage	Part Number	Colour	Colour	Colour
MR810ALU	230 V~	095 428 323	Brown	Blue	Green / Yellow		Schuko
MR810AGU
MR810AFU
MR810ARU
MR810ANU

MR810AEA	230 V~	095 428 317	Brown	Blue	Green / Yellow		Australasian

MR810AEK	230 V~	095 428 569	Brown	Blue	Green / Yellow		UK

MR810AEU	230 V~	095 428 856	Brown	Blue	Green / Yellow		No Plug

MR810ADU	230 V~	095 428 854	Brown	Blue	Green / Yellow		Danish

MR810JHU	115 V~	095 428 322	Brown or	Blue or	Green / Yellow		USA
MR810JSU			Black	White			Right angle
							Right angle

MR810GJU	100 V~	095 428 869	Brown or	Blue or	Green/Yellow		Japanese
			Black	White

MR810 Technical Manual Revision C REF 185042601

27

Contents

Page International United States Australia China Guangzhou Representative Office CONTENTS ELECTRICAL SAFETY TESTS ERFORMANCE EST ROCEDURE APPENDIX A: MAINTENANCE CHECKLIST 1 GENERAL INFORMATION 1.1INTRODUCTION 1.2GLOSSARY OF TERMS 1.3DEFINITIONS 1.4 SYMBOLS 1.5TECHNICAL MANUAL REVISION HISTORY 2SPECIFICATIONS MECHANICAL ELECTRICAL PERFORMANCE Temperature 2.4TRANSPORT AND STORAGE 2.5STANDARDS 3OPERATION AND CONTROLS 3.1 APPLICATION 3.2WARNINGS AND CAUTIONS 3.3SETUP 3.4CONTROLS AND INDICATORS 3.4.3"SEE MANUAL" INDICATOR Hardware Fault Microprocessor Fault 3.4.4 HEATER-WIRE INDICATOR 3.4.5AMBIENT TEMPERATURE SENSOR 3.5OPERATION 3.6DIAGNOSTIC PORT 4MAINTENANCE & CLEANING PROCEDURES 4.1CLEANING 4.2ANNUAL MAINTENANCE Page 5.2SEE MANUAL CODES See Fault Description Section Setting 6SERVICING PROCEDURES 6.1PRECAUTIONS 6.2OPENING THE CASE AND REMOVING THE PCB Figure 6.1: Removing the case bottom 6.2.2 REMOVING THE PCB 6.2.2 R PCB Figure 6.2: Removing the PCB 6.3REPLACING FUSES Model Supply Voltage Fuse Type Part Number 6.4REPLACING THE PCB PCB 6.5SERVICING THE HEATER PLATE Exploded Screw Application Driver Heater Plate Resistance Page Element 6.6REPLACING THE POWER CABLE OR HEATER-WIRE ADAPTOR Supply Power Cable Phase Neutral Page 6.7REPLACING THE PUSH BUTTONS AND THE LED LIGHT PIPE 6.8ASSEMBLING THE PCB AND CASE 6.9COMPLETING THE SERVICE 7ELECTRICAL SAFETY TESTS 7.1PROTECTIVE EARTH RESISTANCE 7.2EARTH LEAKAGE CURRENT 7.3INSULATION RESISTANCE 8PERFORMANCE TEST PROCEDURE 8.1INTRODUCTION 8.2FUNCTIONAL CHECK 8.3HEATER-WIRE MODE PERFORMANCE CHECK 8.4NON HEATER-WIRE MODE PERFORMANCE CHECK Appendix A: MAINTENANCE CHECKLIST Appendix A: M Pass/Fail Visual Check (refer § 4.1) Electrical Safety Check (refer § 7) Performance Check (refer § 8) Appendix B: PRODUCT HISTORY Date Change First Serial # Description of Change Appendix C: D Description (Figure 8.1) C.2 MR810 EXPLODED DIAGRAM C.3 HEATER PLATE PARTS LIST (Figure 8.2) C.4 HEATER PLATE EXPLODED DIAGRAM Appendix D: ELECTROMAGNETIC COMPATIBILITY Appendix D: E D.1 COMPLIANCE AND WARNINGS D.2 ELECTROMAGNETIC EMISSIONS D.3 ELECTROMAGNETIC IMMUNITY Recommended separation distance Recommended separation distances between portable and mobile RF communications equipment and the MR810 Rated maximum output Separation distance according to the frequency of transmitter (m)