Honeywell HD40 manual

USER INFORMATION:

CAUTIONRISK OF ELECTRIC SHOCKDO NOT OPEN

CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

P/N:3810-0071G Rev 0 03/18

SPECIFICATIONS:

Design and specifications are subject to change without notice.

HD40 Series

Explanation of two Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance- (servicing) instructions in the literature accompanying the appliance.

Signal System	NTSC : 525 Lines	PAL : 625 Lines
Scanning System	2 : 1 Interlace
Scanning Frequency (H)	15.734kHz	15.625kHz
Scanning Frequency (V)	59.94Hz	50Hz
Image Sensor	1/3 inch SONY Super HAD CCD
Total/Effective Pixels No.	270K/250K	320K/290K

Operation

Manual

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"

PRECAUTION:

All the warnings and instructions of this manual should be followed.

Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use water damped cloth for cleaning.

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

Do not place anything on top of the unit that might spill or fall into it.

Do not attempt to service this unit yourself as opening or removing covers may you to dangerous voltage or other hazards. Please refer all servicing to qualified service personnel.

Keep enough space around the unit for ventilation.Slots and openings on the monitor should not be blocked.

During flashes of lightning or cracks of thunder, or when the system is not used for a long time, unplug the system power supply to protect the unit from lightening or power surges.

S/N Ratio	More than 48dB
Resolution	380 TV Lines
Video Output Level	1.0 Vp-p (75 Ohms, composite)
Lens- Mirror Cover	Fixed Lens (f=3.8mm)
Focus		Manual
Sync. System		Internal
Sensitivity		0.1 Lux
Electronic Shutter	1/60~100,000 Sec.		1/50~100,000 Sec.
White Balance		Auto
AGC		Auto
Input/Output Connector	Power (Red Jack), Video (Yellow Jack)
Power Consumption	12VDC (10V~15V), 0.15A / 1.8W (Max)
Dome Size (Ø)		85mm
Weight	Approx. 210g

Need Help?Call 1.800.796.CCTV for sales, service and customer support.www.honeywellvideo.com

•1/3” SONY Super HAD CCD

•380 TV Lines Resolution

•Built-in Fixed Lens (f=3.8mm)

•Min. Illumination : 0.1 Lux

•Auto White Balance

•Diameter of Bubble : 85mm

•Easy Install (3-Axis)

		le to i	ns
		p	ns
		m	t
	i			a
	S			l
•				l
•

READ AND KEEP THIS OPERATION MANUAL

INSTALLATION:

This manual explains the installation and operating method for the color dome camera. Before installation, make sure you are familiar with this product's special features and proper operating technique.

COMPOSITION:

Dome Camera	Guide Pattern

90º

	Built-in3-axiscamera	Tilt
	bracket makes it much	360º
	easier to rotate in any
		Horizontal
	direction.
		360º

1 Stick the guide pattern on the wall or ceiling.

2 Drill two holes according to the guide pattern then insert anchors into the drilled holes.

3 Draw out power/video wires to the connecting places.

Ceiling

Guide Pattern

Dome Base

Mounting Screw

Operation Manual

CONNECTION:

TROUBLESHOOTING:Pan

If you have trouble operating your camera, refer to the following.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

4 Fixed the camera to a celling using two screws.

5 Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand.

6 Put the dome cover over the base.

Mounting

Screw

12VDC Power Type

#1	Video	Video Output
	(Yellow)
		GND
#2	Power - 12VDC
#2	(Red)

•The wire is polarized.•Use 12VDC power source.

No.	Function	Terminal Color	Remark

#1	Video Output	Yellow	1.0 Vp-p

#2	Power Input	Red	12VDC(10V~15V),
#2	Power Input	Red	1.8W(Max)
			1.8W(Max)

The image does not	Check the power source for the monitor
appear on the screen.	and camera and ensure that the voltage
	and polarity are properly connected and
	being supplied correctly.

The image on the	Check if the lens is stained. If dirty,
screen is dim.	clean the lens with a soft, clean cloth.
	Adjust the Back Focus of the lens again.

7 Fix the dome cover on the base by covering.

Dome Cover
NOTE	3.02” (76.7mm)
Insert coin to the side	3.02” (76.7mm)
hole and remove the
dome cover by twist coin.

DIMENSIONS:

		4.45”
		(113 mm)
1.34”	(34 mm)					”
					8		)
				.1			)
			0			m
		-				m
	(42.7 mm)	2			m
			.5
1.68”		(4
1.68”
		3.35”					3.35”
		(85 mm)					(85 mm)

The camera does not	Check if you have connected the camera
work properly, the surface	to a proper power source and If there is
of the camera case is hot,	no problem with the power, turn the unit
and a black line appears	off immediately and seek assistance from
on the screen.	our Customer Service department.

The screen blinks a lot.	Check if the camera is pointed toward
	the sun or a fluorescent lamp.
	Adjust the angle or location of the
	camera if too much light is coming into
	the screen.