Honeywell HD60 manual

	You must be fully aware of all the distinctive
COMPOSITION:	features and precautions related to this
	camera before installing it.

	Guide Pattern
	Service Monitor Cable
Operation Manual	Mounting Screw

DIMENSIONS(mm):

100.0
	51.0
	75.7	102.0
	37.3
130.6	13.7

HD60 Series

INSTALLATION:

1Stick the guide pattern on the wall or ceiling.

2Drill four holes according to the guide pattern then insert anchors into the drilled holes.

3Draw out power / video wires to the connecting places.

Ceiling Guide Pattern Dome Base

SPECIFICATIONS:

Model	NTSC		PAL
Signal System	NTSC : 525 Lines		PAL : 625 Lines
Scanning System		2 : 1 Interlace
Scanning Frequency (H)	15.734kHz		15.625kHz
Scanning Frequency (V)	59.94Hz		50Hz
Image Sensor	1/3" SONY Super HAD CCD

Operation

Manual

• 1/3"	Sony Super HAD CCD
• 380	TV Lines Resolution

4Fixed the camera to a celling using four screws.

5Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand.

6Put the dome cover over the base.7Fix the dome cover on the base by covering.

MountingScrew Dome Cover NOTEInsert coin to the side hole and remove the dome cover by twist coin.

Total / Effective Pixels No.	270K / 250K		320K / 290K
S / N Ratio	More than 48dB (AGC Off)
Resolution	380 TV Lines
Video Output Level	1.0 Vp-p (75 Ohms, composite)
Lens	Fixed Lens : f=4.0mm, 81º
Focus		Manual
Sync. System		Internal
Sensitivity	0 Lux, IR LED
Electronic Shutter	1/60 ~ 100,000 Sec.		1 /50 ~ 100,000 Sec.
White Balance		Auto
AGC		On / Off
BLC	On / Off (with Slide Switch)
Flickerless	On / Off (with Slide Switch)
Input / Output Connector	Power, Video
Power Consumption	12VDC (10.8V~15V), 0.4A / 5W (Max)
Dome Size (Ø)		100mm
Weight	Approx. 366g

Need Help?Call 1.800.796.CCTV for sales, service and customer support.www.honeywellvideo.com

P/N:3810-0072H Rev 0 03/18

• 4mm Fixed Lens

• Color Day/Night with 24 LEDs

• Auto White Balance

• AGC, BLC, Flickerless On/Off

• Extra Video Output for Installer

• 3-Axis Camera Construction

• Diameter of Bubble : 100mm

		le to i	n
		p
		m	s
			t
	i			a
	S			l
•				l

READ AND KEEP THIS OPERATION MANUAL

PRECAUTIONS:

! Do not install the camera in

extreme temperature conditions.

Do use the camera under conditions where

NAME AND FUNCTION:

Fixed Lens & IR LED Type

Design and specifications are		90º
subject to change without notice.	Built-in3-axiscamera
	bracket makes it much	360º
	easier to rotate in any

5 direction.

	temperatures are within -10°C to 45°C.
	Be especially careful with ventilation
	under high temperatures.
!	Do not install or use the camera
	in an environment where the
	humidity is high.
	It can cause the image quality to be poor.
!	Do not disassemble the camera.
	There are no user-serviceable parts
	inside it.
!	Do not drop the camera or
	subject them to physical shocks.
	It can cause malfunctions to occur.

1

2

1	Tilt rotation: Adjusting the vertical angle.
2	Pan rotation: Adjusting the horizontal angle.

4	CAMERA SET-UP:
	Fixed Lens & IR LED Type
3
					b
			IO			LEVELDC	VIDEO
		05
		J5
		AT	ER	AC 24V
	E	/AUD					12 3 SWITCH
	H			J503		ON
					BLC ON
					AGC OFF
					FL ON

4IR LED: 850nm / 30°(24EA)

			360º
J502	J504	a	Function Selection Switch:
			•FL(Flickerless) ON/OFF
J501	AC24V
			•AGC(Auto Gain Control) ON/OFF
			•BLC(Back Light Compensation)

ON/OFF

bService Monitor Connecter: Use service monitor connector to set camera angle & focus when installing.

CAUTION : When AGC is off,

aD/N does not work because the D/N switching function is dependent on the AGC level.

! Note

When this camera is installed near

3 Horizontal rotation: Adjusting the horizontal

position of the screen.

5Sensor

Camera Lay-out TROUBLESHOOTING:

wireless communication devices

that emits strong electromagnetic

field, irregularity such as noise on

the monitor may appear.

CONNECTION:

#1

Connecting toMonitor and Power

12VDC Power Type #2

IR LED (4mm Fixed Lens)

Video	Video Output
(Yellow)
	GND
Power - 12VDC
(Red)

•Power Consumption: 5W•IR LED Specification: 850nm / 30°(24EA)•The wire is polarized. • Use 12VDC power source.

No.	Function	Terminal Color	Remark
#1	Video Output	Yellow	1.0 Vp-p
#2	Power Input	Red	12VDC(10.8V~15V), 0.4A/5W(Max)

If you have trouble operating your camera, refer to the following.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

The image does not	Check the power source for the monitor and camera
appear on the screen.	and ensure that the voltage and polarity are properly
	connected and being supplied correctly.
The image on the	Check if the lens is stained. If dirty, clean the lens with
screen is dim.	a soft, clean cloth.
	Adjust the Back Focus of the lens again.
The camera does not work	Check if you have connected the camera to a proper
properly, the surface of the	power source and If there is no problem with the power,
camera case is hot, and a black	turn the unit off immediately and seek assistance from
line appears on the screen.	our Customer Service department.
The screen blinks a lot.	Check if the camera is pointed toward the sun or a

fluorescent lamp.

Adjust the angle or location of the camera if too much light is coming into the screen.