Manuals / Brands / Lawn and Garden / Lawn Mower / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna DRT70 TO REPLACE GROUND DRIVE BELT (See Figs. 25 and 26), GROUND DRIVE BELT ADJUSTMENT (See Fig. 26)

1 28

Download 28 pages, 941.7 Kb

16

SERVICE AND ADJUSTMENTS

CABLE CLIP

SCREW

DRIVE

CONTROL

CABLE

EXTENSION

SPRING

ENGINE

PULLEY

IDLER

PULLEY TRANS MIS SION

PULLEY

LESS

TEN SION

5/8" MORE

TEN SION

FIG. 26

TO REPLACE GROUND DRIVE BELT (See Figs. 25 and 26)

• Remove belt guard as described in “TO REMOVE BELT

GUARD”.

• Remove old belt by slipping off engine pulley first then

remove from transmission pulley.

• Place new belt in groove of transmission pulley and

into engine pulley. BELT MUST BE IN GROOVE ON

TOP OF IDLER PULLEY. NOTE POSITION OF BELT

TO GUIDES.

• Check belt adjustment as described below.

• Replace belt guard.

• Reposition wheel and replace clevis pin and hairpin

clip.

GROUND DRIVE BELT ADJUSTMENT (See Fig. 26)

For proper belt tension, the extension spring should have

about 5/8 inch (16 mm) stretch when drive control bar is

in “EN GAGED” position. This tension can be attained as

fol lows:

• Loosen cable clip screw securing the drive control

cable.

• Slide cable forward for less tension and rearward for

more tension until about 5/8 inch (16 mm) stretch is

obtained while the drive control bar is engaged.

• Tighten cable clip screw securely.

Contents

Main MAINTENANCE AND STORAGE - IMPORTANT - SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers TRAINING PREPARATION OPERATION WARNING TABLE OF CONTENTS PRODUCT SPECIFICATIONS TOOLS REQUIRED FOR ASSEMBLY OPERATORS POSITION (See Fig. 1) CONTENTS OF HARDWARE PACK UNPACKING CARTON (See Fig. 2) INSTALL HANDLE (See Figs. 3, 4, and 5) REMOVE TILLER FROM CRATE CONNECT SHIFT ROD (See Fig. 7) ATTACH CLUTCH CABLE (See Fig. 6) CHECK TIRE PRESSURE HANDLE HEIGHT KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. MEETS ANSI SAFETY REQUIREMENTS HOW TO USE YOUR TILLER STOPPING (See Fig. 9) TINE OPERATION - WITH WHEEL DRIVE FORWARD - WHEELS ONLY/TINES STOPPED REVERSE - WHEELS ONLY/TINES STOPPED TO TRANSPORT BEFORE START ING ENGINE CHECK ENGINE OIL LEVEL (See Fig. 13) TURNING CULTIVATING TILLING HINTS (See Fig. 15) ADD GASOLINE TO START ENGINE (See Fig. 14) CULTIVATING (See Fig. 16) ADJUST WHEELS FOR CULTIVATING (See Figs. 17 and 18) GENERAL RECOMMENDATIONS LUBRICATION CHART BEFORE EACH USE LUBRICATION MAINTENANCE SCHEDULE LUBRICATION AIR FILTER (See Fig. 21) MUFFLER SPARK PLUG TRANSMISSION CLEANING COOLING SYSTEM (See Fig. 22) TILLER TO ADJUST HANDLE HEIGHT (See Fig. 23) TO REMOVE BELT GUARD (See Fig. 25) TIRE CARE TO REMOVE WHEEL (See Fig. 24) TO REPLACE GROUND DRIVE BELT (See Figs. 25 and 26) GROUND DRIVE BELT ADJUSTMENT (See Fig. 26) TINE REPLACEMENT (See Figs. 27, 28 and 29) TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30) TO AD JUST CARBURETOR STORAGE ENGINE OIL CYLINDER(S) OTHER TILLER TROUBLESHOOTING POINTS HANDLE ASSEMBLY MAINFRAME, LEFT SIDE MAINFRAME, RIGHT SIDE TRANSMISSION TINE SHIELD TINE ASSEMBLY DECALS