Manuals / Brands / Lawn and Garden / Lawn Mower / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna DRT70 REMOVE TILLER FROM CRATE, CONNECT SHIFT ROD (See Fig. 7), ATTACH CLUTCH CABLE (See Fig. 6), CHECK TIRE PRESSURE, HANDLE HEIGHT

1 28

Download 28 pages, 941.7 Kb

6

ASSEMBLY

SHIFT

ROD

HAIRPIN

CLIP

SHIFT

LEVER

INDICATOR

REMOVE TILLER FROM CRATE

• Make sure shift lever indicator is in “N” position (See

Fig. 7)

• Tilt tiller forward by lifting handle. Separate cardboard

cover from leveling shield.

• Rotate tiller handle to the right and pull tiller out of

carton.

CONNECT SHIFT ROD (See Fig. 7)

• Insert end of shift rod into hole of shift lever indicator.

• Insert hairpin clip through hole of shift rod to secure.

FIG. 7

FIG. 6

END OF CLUTCH

CABLE

CONTROL

BAR

CONTROL BAR

BRACKET

CONTROL BAR

BRACKET

CLUTCH

CABLE

ATTACH CLUTCH CABLE (See Fig. 6)

• Hook end of clutch cable through hole in control bar

bracket.

CHECK TIRE PRESSURE

The tires on your unit were overinflated at the factory for

shipping purposes. Correct and equal tire pressure is

important for best tilling performance.

• Reduce tire pressure to 20 PSI (1.4 kg/cm2).

HANDLE HEIGHT

• Handle height may be adjusted to better suit operator.

(See “TO ADJUST HANDLE HEIGHT” in the Service

and Adjustments section of this manual).

Contents

Main MAINTENANCE AND STORAGE - IMPORTANT - SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers TRAINING PREPARATION OPERATION WARNING TABLE OF CONTENTS PRODUCT SPECIFICATIONS TOOLS REQUIRED FOR ASSEMBLY OPERATORS POSITION (See Fig. 1) CONTENTS OF HARDWARE PACK UNPACKING CARTON (See Fig. 2) INSTALL HANDLE (See Figs. 3, 4, and 5) REMOVE TILLER FROM CRATE CONNECT SHIFT ROD (See Fig. 7) ATTACH CLUTCH CABLE (See Fig. 6) CHECK TIRE PRESSURE HANDLE HEIGHT KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. MEETS ANSI SAFETY REQUIREMENTS HOW TO USE YOUR TILLER STOPPING (See Fig. 9) TINE OPERATION - WITH WHEEL DRIVE FORWARD - WHEELS ONLY/TINES STOPPED REVERSE - WHEELS ONLY/TINES STOPPED TO TRANSPORT BEFORE START ING ENGINE CHECK ENGINE OIL LEVEL (See Fig. 13) TURNING CULTIVATING TILLING HINTS (See Fig. 15) ADD GASOLINE TO START ENGINE (See Fig. 14) CULTIVATING (See Fig. 16) ADJUST WHEELS FOR CULTIVATING (See Figs. 17 and 18) GENERAL RECOMMENDATIONS LUBRICATION CHART BEFORE EACH USE LUBRICATION MAINTENANCE SCHEDULE LUBRICATION AIR FILTER (See Fig. 21) MUFFLER SPARK PLUG TRANSMISSION CLEANING COOLING SYSTEM (See Fig. 22) TILLER TO ADJUST HANDLE HEIGHT (See Fig. 23) TO REMOVE BELT GUARD (See Fig. 25) TIRE CARE TO REMOVE WHEEL (See Fig. 24) TO REPLACE GROUND DRIVE BELT (See Figs. 25 and 26) GROUND DRIVE BELT ADJUSTMENT (See Fig. 26) TINE REPLACEMENT (See Figs. 27, 28 and 29) TO ADJUST THROTTLE CONTROL CABLE (See Fig. 30) TO AD JUST CARBURETOR STORAGE ENGINE OIL CYLINDER(S) OTHER TILLER TROUBLESHOOTING POINTS HANDLE ASSEMBLY MAINFRAME, LEFT SIDE MAINFRAME, RIGHT SIDE TRANSMISSION TINE SHIELD TINE ASSEMBLY DECALS