IBM C1B 1.12 Brick On Sled Carrier 128-pin HPC, C1C 1.12 3.5-inch Small FF 38-pin Unitized, C2B 2.25 Brick On Sled carrier 128-pin HPC, C4B 4.51 Brick On Sled carrier 128-pin HPC, C4C 4.51 3.5-inch Small FF 38-pin Unitized, SSA 2.2.8 Bring-up Sequence (and Stop) Times

USER RESPONSIBLE FOR VERIFYING VERSION AND COMPLETENESS

OEM FUNCTIONAL SPECIFICATION ULTRASTAR XP (DFHC) SSA MODELS 1.12/2.25 GB -1.0" HIGH

2.2.8 Bring-up Sequence (and Stop) Times

Figure 10. Start Time Diagram

Note: BATS is the abbreviation for Basic Assurance Tests. Start-up sequence spins up the spindle motor,

initializes the servo subsystem, up-loads code, performs BATS2 (verifies read/write hardware), resumes

"Reassign in Progress" operations, and more. For more information o n the start-up sequence, refer to the

Ultrastar XP (DFHC) SSA Models Interface Specification.

Note: If a RESET is issued before the drive comes ready, the power o n sequence will start again. In all

other cases when a RESET is issued the present state of the motor is not altered.

Note: Reference “Start/Stop Unit Time” on page 49 for additional details.

Note: See 5.7, “Spindle Synchronization” on page 69 for details about Start-up time increases when the

device is requested via Mode Parameters to synchronize the spindle motor to another device.

Table 3. Bring-up Sequence Times and Stop Time for C1x Models

Event Nominal Maximum Notes

Power-up 1.5 sec 2.0 sec *see Figure 10

Start-up 12.4 sec 45 sec. *see Figure 10

Spin-up 8.2 sec 29.2 sec *see Figure 10

Spindle Stop 6.0 sec 12.0 sec

Source filename=BRINGUPIBM CorporationPage 36 of 87

Contents

Main Page Preface Page Contents Page Page Page 1.0 Description 1.1 Features 1.1.1 General Features 1.1.2 Performance Summary 1.1.3 Interface Controller Features 1.2 Models 2.0 Specifications 2.1 General Page 2.1.1 Capacity Equations 2.1.1.1 For Each Notch 2.1.1.2 For Entire Drive 2.2 Power Requirements by Model 2.2.1 C1x Models 2.2.1.1 Power Calculation Examples Page Page Page Page 2.2.2 C2x Models 2.2.2.1 Power Calculation Examples Page Page Page Page 2.2.3 C4x Models 2.2.3.1 Power Calculation Examples Page Page Page Page 2.2.4 CxB Models 2.2.4.1 Power supply methods 2.2.4.2 DC/DC Converter 2.2.5 Power Supply Ripple 2.2.6 Grounding Requirements of the Disk Enclosure 2.2.7 Hot plug/unplug support Page 2.2.8 Bring-up Sequence (and Stop) Times Page Page 3.0 Performance 3.1 Environment Definition 3.2 Workload Definition 3.2.1 Sequential 3.2.2 Random 3.3 Command Execution Time 3.3.1 Basic Component Descriptions Page 3.3.2 Comments 3.3.2.1 Theoretical Data Sector Transfer Rate 3.4 Approximating Performance for Different Environments 3.4.1 For Different Transfer Sizes 3.4.2 When Read Caching is Enabled 3.4.3 When Write Caching is Enabled 3.4.4 When Adaptive Caching is Enabled 3.4.5 When Read-ahead is Enabled 3.4.6 When No Seek is Required 3.4.7 For Queued Commands 3.4.7.1 Reordered Commands 3.4.7.2 Back-To-Back Commands 3.4.8 Out of Order Transfers 3.5 Skew 3.5.1 Cylinder to Cylinder Skew 3.5.2 Track to Track Skew 3.6 Idle Time Functions 3.6.1 Servo Run Out Measurements 3.6.2 Servo Bias Measurements 3.6.3 Predictive Failure Analysis 3.6.4 Channel Calibration 3.6.5 Save Logs and Pointers 3.7 Command Timeout Limits Page 4.0 Mechanical 4.1 Small Form Factor Models (CxC) 4.1.1 Weight and Dimensions 4.1.2 Clearances 4.1.3 Mounting Page Page Page Page Page 4.2 Carrier Models (CxB) 4.2.1 Weight and Dimensions 4.2.2 Clearances 4.2.3 Mounting Page Page 4.2.4 Auto-docking Assembly Side Rails Page Page 5.0 Electrical Interface 5.1 SSA Unitized Connector 5.2 Carrier Connector Page 5.3 SSA Link Cable 5.4 SSA Link Electrical Characteristics 5.5 Option Pins and Indicators 5.5.1 - Manufacturing Test Mode (Option Port Pin 1) 5.5.2 - Auto Start Pin (Option Port Pin 2) 5.5.4 - Write Protect (Option Port Pin 4) 5.5.5 - Ground long (Option Port Pin 5) 5.5.6 - Device Activity Pin/Indicator (Option Port Pin 6) 5.5.7 + 5V (Option Port Pin 7) 5.5.8 - Device Fault Pin/Indicator (Option Port Pin 8) 5.6 Front Jumper Connector 5.7 Spindle Synchronization 5.7.1 Synchronization overview 5.7.2 Synchronization Mode 5.7.3 Synchronization time 5.7.4 Synchronization with Offset 5.7.5.2 Over Sync Hard-wire Page Page 6.0 Reliability 6.1 Error Detection 6.2 Data Reliability 6.3 Seek Error Rate 6.4 Power On Hours Examples: Page 6.7 *Mean Time Between Failure (*MTBF) 6.7.1 Sample Failure Rate Projections 6.8 SPQL (Shipped product quality level) 6.9 Install Defect Free Page 7.0 Operating Limits 7.1 Environmental 7.1.1 Temperature Measurement Points Page 7.2 Vibration and Shock 7.2.1 Drive Mounting Guidelines 7.2.2 Output Vibration Limits 7.2.3 Operating Vibration 7.2.3.1 Nonoperating Vibration 7.2.4 Operating Shock 7.2.5 Nonoperating Shock 7.3 Contaminants 7.4 Acoustic Levels Page 8.0 Standards 8.1 Safety 8.2 Electromagnetic Compatibility (EMC) Page Bibliography