Introduction | ICP DAS USA 100-700 PLCS, DB25, DN-3000 specification

Introduction

INTRODUCTION

The DN-3000 is an intelligent, multiple-function DeviceNet Data Transfer Unit designed for use within the harsh industrial environment.

Using the DN-3000 Configuration Editor Software program, the DN-3000 can be programmed to run either of the two (2) following application types:

1)DEVICENET TO PLCS OR DEVICES Allows a DeviceNet Host to read or write data registers in one or more PLCs or Devices that use the same protocol. One of the DN-3000’s three ports can be used as a pass-through port in which all messages received are simply passed through to one of the connected PLCs/Devices (if supported for that PLC/Device protocol), allowing PLC programming software, a third party’s intelligent (MMI) Man-Machine Interface terminal or a SCADA software program to be “connected” to the same port on the PLCs/Devices used by the DN-3000.

2)DEVICENET TO MOTOR DRIVES Allows a DeviceNet Host to control and/or monitor parameters in up to 32 Motor Drives.

This manual is presented in two sections. Each section deals with the configuration requirements for each of the above applications: DeviceNet to PLCs and DeviceNet to Motor Drives.

Please note that the application type is selected when a new project is created using the DN-3000 configuration software and may not be changed after the project is created.

1

Image 7

ICP DAS USA 100-700 PLCS, DB25, DN-3000 user manual Introduction

Contents

DN-3000 Page Warranty Warranty & Notices Table of Contents Application Notes Motor Drives Page Introduction Introduction Installation Software InstallationGeneral Information Software START-UP Software Information Creating a Project File Creating Project Files Project Types Additional Project Menu Sub-Headings Devicenet to Plcs or Devices DeviceNet to PLCs or DevicesDevice Profile DeviceNet Host to Serial PLC with Pass-Through Connection Example ApplicationsDeviceNet Host to Multi-Dropped Serial PLCs Multiple DN-3000s with Different PLC or Device Types DeviceNet to PLCs or Devices Edit Menu Configuring Port #1, Devicenet MAC ID of DN3000 PLC/Device Protocol Configuring Port #2 Plcs or Devices Wire RS422 or RS485 Communications Intermessage Time-Out Configuring Port # 3 Passthrough Use I/O Data Data Configuration Output Data Use Command BlockUse Diagnostics Output Data Size Input Data Input Data Size Output Data Table Register Number Use Output WordPLC/Device Address File Number Allen-Bradley PLCs only Input Data Table PLC/DeviceAddress Use Input Word Command Block Devicenet to Motor Drives DeviceNet to Motor Drives DeviceNet Host to Multi-Dropped Serial Motor Drives DeviceNet Host to Serial Motor Drive Multiple DN-3000s with Different Motor Drive Types DeviceNet to Motor Drives Edit Menu MAC ID of DN3000 Motor Drive Type Configuring Port # 2 Motor Drives Minimum Delay Between Messages Data Configuration Use Command Block Input Data Size Output Data Table Parameter Number Motor Drive Address Input Data Table Use Input Word Number Word Returned Parameter Data read command only Word Motor Drive Address CommandNumber Word Parameter Data write command only Word Motor Drive Address Result Code Command Operation of the Link Switch Upper Link Configuration Mitsubishi Drives Only Exception Table Mitsubishi Drives Only Transferring Project Files Transferring Project Files Verify Transfer OptionsDownload Project to DN3000 Upload Project from DN3000 Options Settings Options SettingsSET Directory Current Directory Path Graphic Area SET COM Port Save Options to Disk Default OptionsSET Printer Options Load Options from Disk Physical Dimensions Power RequirementsTechnical Information Visual LED Indicators DIP Switch SettingsSwitch # Normal Off Configuration Diagnostic Flashes followed by a pause Invalid DIP Switch Setting DN-3000 Troubleshooting InformationFlashes followed by a pause Protocols Supported Registers AccessedApplication Notes PLCs and Devices ALLEN-BRADLEY PLC 5, SLC500 and Micrologix Plcs Idec FA Series Plcs Idec MICRO-3 PlcsLink Adapter Requirement Koyo / PLC Direct 205 Series Plcs Memory Address PLC Registers Accessed Koyo / PLC Direct / TI 305 Series Plcs RTS Control Mitsubishi FX Series PlcsModicon Plcs and Modbus Devices Omron Plcs Pass-Through Port Protocol Information Passthrough Port Note Square D Model 100-700 Plcs Toshiba T Series Plcs Toshiba EX and M Series PlcsWestinghouse Plcs Baldor Motor Drives Application Notes Motor DrivesDrive Parameter Numbers Assigned By Panel-Tec Drive Addresses Assigned By Panel-Tec Configuring a Baldor Drive For Serial Communications Yaskawa Motor Drives Configuring a Woods Drive For Serial CommunicationsMitsubishi Motor Drives Woods Motor Drives DN3000 Configuration Cable Cable Diagrams Solder End Allen Bradley GE Fanuc DN3000 GE Fanuc 90/20, 30 Idec Koyo/PLC Direct Mitsubishi Mitsubishi FX Series Modicon Modicon Host Link Omron Siemens S7 TSX07 Square D TI5 232 Port DN3000 Simatic TI5 Series Toshiba DN3000 Toshiba Baldor Baldor Motor Drives Mitsubishi Motor Drives Woods Motor Drives Yaskawa Motor Drives DeviceNet DN3000 DeviceNet Cable