E2010 CCN15197205
(800) 276-4658 DFAX(800) 266-7016
INGERSOLL RAND COMPANY LTD
209 NORTHMAIN STREET --BRYAN, OHIO 43506

1-1/2” DIAPHRAGM PUMP

OPERATOR’S MANUAL PD15P-X
RELEASED: 9-5 -03
REVISED: 5-12-10
(REV.12)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1:1 RATIO (NON-METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator.Keep for future reference.

PE15P-X

SERVICE KITS

Refer to Model Description Chart to match the pump material options.
637389 for air section repair (see page 6).
637391-XXfor fluid section repair (see page 4). NOTE: This kit also con-
tains several air motor seals which will need to be replaced.
637390-X major air valve assembly (see page 7).

PUMP DATA

Models see Model Description Chart for “-XXX”...........
Pump Type Non-MetallicAir Operated Double Diaphragm.......
Material see Model Description Chart...........
Weight PX15P-FKS-XXX 63.94lbs (29.00 kgs)... .......
PX15P-FPS-XXX 42.60lbs (19.32 kgs).......
PX15P-YKS-XXX 55.94lbs (25.37 kgs).......
PX15P-YPS-XXX 42.30lbs (19.19 kgs).......
Maximum Air Inlet Pressure 120 p.s.i.g. (8.3 bar).........
Maximum Material Inlet Pressure 10 p.s.i.g. (0.69 bar).....
Maximum Outlet Pressure 120 p.s.i.g. (8.3 bar)..........
Maximum Flow Rate (flooded inlet)123.1 g.p.m. (465.9 l.p.m.)....
Displacement / Cycle @ 100 p.s.i.g. 0.617 gal. (2.34 lit.)...
Maximum Particle Size 1/4” dia. (6.4 mm)............
Maximum TemperatureLimits (diaphragm / ball / seal material)
E.P.R./ EPDM -60_to280_F(-51_to138_C)...........
HytrelR-20_to 150_F(-29_to 66_C)................
Nitrile 10_to 180_F(-12_to 82_C).................
Polypropylene 35_to 175_F(2_to 79_C)...........
PVDF (KynarR)10_to 200_F(-12_to93_C)..........
SantopreneR-40_to225_F(-40_to107_C)...........
PTFE 40_to 225_F(4_to 107_C).................
VitonR-40_to350_F(-40_to177_C)................
Dimensional Data see page 8................
Mounting Dimension 8.687”x 14.937” (220.7 mm x 379.4 mm)...
Noise Level @ 70 p.s.i., 60 c.p.m. 81.0 db(A){.....
Thepump sound pressure levels published here have been updated to an Equivalent
ContinuousSound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROPS5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult arepresentative or the
factory if you have questions concerning availability.
PX15P-FXS-XXX PX15P-YXS-XXX

MODEL DESCRIPTION CHART

PX15 P -X X S -X X X
PX15P - XXS - X X X
637391 - X X
DiaphragmBall
FLUIDSECTION SERVICE KIT SELECTION
EXAMPLE:Model # PD15P-FPS-PAA
FluidSection Service Kit # 637391-AA
Seat Material
H - Hard 440 Stainless Steel
K - PVDF (Kynar)
P - Polypropylene
S - 316 Stainless Steel
Diaphragm Material
A - Santoprene M - Medical Grade Santoprene
C - Hytrel T -PTFE /Santoprene
G - Nitrile V - Viton
Hardware Material
S - Stainless Steel
Fluid Caps & Manifold Material
K - PVDF (Kynar)
P - Polypropylene
Fluid Connection / Location
F - 1-1/2” A.N.S.I. / Din Flange / End
Y - 1-1/2” A.N.S.I. / Din Flange / Center
Center Section Material
P - Polypropylene
Ball Material
A - Santoprene S - 316 Stainless Steel
C - Hytrel T -PTFE
G - Nitrile V - Viton
Electronic Interface
D - None
E - Available
www.ingersollrandproducts.com