E2010 CCN99756587
(800) 276-4658 DFAX(800) 266-7016
INGERSOLL RAND COMPANY
209 NORTHMAIN STREET- BRYAN, OHIO 43506
OPERATOR’S MANUAL PD30X -X-B
RELEASED: 8-14-98
REVISED: 5-7-10
(REV.P)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

3” DIAPHRAGM PUMP

1:1 RATIO (METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator.Keep for future reference.

SERVICE KITS

Refer to Model Description Chart to match the pump material options.
637303-XXfor fluid section repair (see page 4). Note: This kit also con-
tains several air motor seals which will need to be replaced.
637302 for air section repair (see page 6).
67089-X major air valve assembly (see page 7)

PUMP DATA

Models see Model Description Chart for “-XXX”..............
Pump Type Metallic Air Operated Double Diaphragm..........
Material see Model Description Chart..............
Weight PD30A-XAX-XXX-B( ) 113lbs (51.3 kgs).... ...
PD30A-XCX-XXX-B( ) 197 lbs(89.4 kgs)...
PD30A-XHX-XXX-B( ) 203 lbs(92.1 kgs)...
PD30A-XSX-XXX-B( ) 203 lbs (92.1 kgs)...
(add 40 lbs [18.1 kg] for stainless steel air motor section)
Maximum Air Inlet Pressure
Ball check models 120 p.s.i.g. (8.3 bar).............
Cone check models 100 p.s.i.g. (6.9 bar)............
Maximum Material Inlet Pressure 10 p.s.i.g. (.69 bar).....
Maximum Outlet Pressure
Ball check models 120 p.s.i.g. (8.3 bar).............
Cone check models 100 p.s.i.g. (6.9 bar)............
Maximum Flow Rate (floodedinlet)
Ball check models 275 g.p.m. (1041 l.p.m.).............
Cone check models 195 g.p.m. (738.1 l.p.m.)............
Displacement / Cycle @ 100 p.s.i.g. 2.8 gal. (10.6 lit.)...
Maximum Particle Size
Ball check models 3/8” dia. (9.5 mm).............
Cone check models 3/4” dia. (18.75 mm)............
Maximum TemperatureLimits (diaphragm / ball / seal material)
E.P.R./ EPDM -60_to280_F(-51_to138_C)...........
HytrelR-20_to 150_F(-29_to 66_C)................
Nitrile 10_to 180_F(-12_to 82_C).................
P.V.D.F.(KynarR)10_to200_F(-12_to 93_C)........
SantopreneR-40_to225_F(-40_to107_C)...........
PTFE 40_to 225_F(4_to107_C).................
VitonR-40_to350_F(-40_to177_C)................
Dimensional Data see page 8................
Mounting Dimensions 10-5/32” x 12-1/16” (258 mm x 306 mm)...
Noise Level @ 70 p.s.i., 50 c.p.m.83.0 db(A)....
Testedwith 67263 muffler assembly installed.
Thepump sound pressure levels published here have been updated to an Equivalent
ContinuousSound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROPS5.1 using four microphone locations.
NOTICE:All possible options are shown in the chart however certain com-
binations may not be recommended, consult a representativeor the fac-
tory if you have questions concerning availability.
3” DIAPHRAGM PUMP
PD30X-XXX-XXX-B( )

MODEL DESCRIPTION CHART

PD30 X -X X X -X X X -B03
PD30X - XXX - X X X-B()
637303 - X X
DiaphragmBall
FLUIDSECTION SERVICE KIT SELECTION
EXAMPLE:MODEL # PD30A-ACS-SAA-B
FLUIDSECTION SERVICE KIT # 637303-AA
SEATMATERIAL
A - Santoprene H -Hard 440 Stainless Steel
C - Hytrel K - PVDF (Kynar)
E - Carbon Steel L -Hastelloy
F - Aluminum S - 316 Stainless Steel
G - Nitrile 0 -(Cone Check)
DIAPHRAGM MATERIAL
A - Santoprene G - Nitrile V - Viton
C - Hytrel T - PTFE
BALL MATERIAL (=)Cone Check models
A - Santoprene J - Nitrile (=)T - PTFE
C - Hytrel K - E.P.R. (=)V-Viton
G - Nitrile L - Viton (=)
HARDWAREMATERIAL
P - Plated Steel S - Stainless S teel
FLUID CAPS & MANIFOLD MATERIAL
A - Aluminum H - Hastelloy
C - Cast Iron S - Stainless Steel
THREAD
A - N.P. T.F. B - BS P
CENTER SECTION MATERIAL
A - Aluminum S - Stainless Steel
CONE CHECK FLOW
03 - Bottom Discharge
www.ingersollrandproducts.com