E2010 CCN15206188
(800) 495-0276DFAX (800) 892-6276
INGERSOLL RAND COMPANYLTD
209NORTH MAIN STREET -- BRYAN,OHIO 43506
1-1/2” DIAPHRAGM PUMP
OPERATOR’S MANUAL PM15X -X-X-A0 2RELEASED: 1-7-0 4
REVISED: 5-12-10
(REV.09)
INCLUDING: OPERATION,INSTALLATION & MAINTENANCE
1:1 RATIO(METALLIC)
READ THIS MANUAL CAREFULLYBEFORE INSTALLING,
OPERATINGOR SERVICING THIS EQUIPMENT.
Itis the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Referto Model Description Chart to match the pump material options.
637389for air section repair (see page 6).
637375-XXfor fluid section repair (see page 4). NOTE: This kit also con-
tainsseveral air motor seals which will need to be replaced.
637390-Xmajor air valve assembly (see page 7).
PUMP DATA
Models seeModel Description Chart for “-XXX”..............
PumpType MetallicAirOperatedDouble Diaphragm..........
Material seeModel Description Chart..............
Weight PM15A-CSS-XXX-A02 62.40 lbs (28.30 kgs)... ...
PM15R-CSS-XXX-A02 60.26 lbs (27.33 kgs)...
PM15S-CSS-XXX-A02 78.40 lbs (35.56 kgs)...
MaximumAir Inlet Pressure 120p.s.i.g. (8.3 bar).........
MaximumMaterial Inlet Pressure 10p.s.i.g. (0.69 bar).....
MaximumOutlet Pressure 120p.s.i.g. (8.3 bar)..........
MaximumFlow Rate (flooded inlet)123 g.p.m. (465.6 l.p.m.)....
Displacement/ Cycle @ 100 p.s.i.g. 0.617gal. (2.34 lit.)...
MaximumParticle Size 1/4”dia. (6.4 mm)............
MaximumTemperature Limits (diaphragm / ball / seal material)
E.P.R./ EPDM -60_to 280_F(-51_to138_C)...........
Polypropylene 35_to175_F(2_to79_C)...........
SantopreneR-40_to225_F(-40_to107_C)...........
PTFE 40_to225_F(4_to107_C).................
DimensionalData seepage 8................
MountingDimension 9”x 11.75”(228.6 mm x 298.5 mm)........
NoiseLevel @ 70 p.s.i., 60 c.p.m. 85.0 db(A){.....
Thepump sound pressure levels published here have been updatedto an Equivalent
ContinuousSound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROPS5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however,certain
combinationsmay not be recommended, consult a representative or the
factoryif you have questions concerning availability.
Figure1
MODEL DESCRIPTION CHART
PM15 X -C S S -X X X -A02
PM15X- CSS - X X X-A02
637375- X X
DiaphragmBall
FLUIDSECTION SERVICE KIT SELECTION
EXAMPLE:Model # PM15S-CSS-SAA-A02
FluidSection Service Kit # 637375-AA
SeatMaterial
A - Santoprene
S - 316 Stainless Steel
DiaphragmMaterial
A - Santoprene
M - Medical Grade Santoprene
T - PTFE / Santoprene
BallMaterial
A - Santoprene
T - PTFE
HardwareMaterial
S - Stainless Steel
FluidCaps & Manifold Material
S - Stainless Steel
FluidConnection
C - Tri-clamp
CenterSection Material
A - Aluminum
R - Polypropylene
S - Stainless Steel
www.ingersollrandproducts.com