![](/images/backgrounds/182209/bg34.png)
48
NS-42E470A13A Insignia 42" 1080p LED TV
www.insigniaproducts.com
Remote control
General
The picture has a few bright
or dark spots. • A few bright or dark spots on an LCD screen is
normal. It does not affect the operation of
yourTV.
Good picture, but no sound. • Increase the volume.
• Make sure that the sound is not muted.
• Make sure you do not have headphones
connected. When headphonesare connected,
no sound comes from the TV speakers.
• Make sure that the correct audio mode is
selected.
• Make sure that the audio cables are connected
correctly and securely to your TV.
• Make sure that the antenna or cable TV is
connected correctly and securely. See
“Connecting a cable or satellite box” on page10
or “Connecting an antenna or cable TV (no box)”
on page13.
• If you are using an antenna, the digital channel
signal may be low. To check the digital channel
signal strength, see “Checking the digital signal
strength” on page30.
• The audio cable(s) you are using may be ba d. Try
a new set.
Poor picture. • Make sure that the room is not too bright. Light
reflecting off the screen can make the picture
difficult to see.
• If an S-VHS camera or a camcorder is connected
while another connected device is turned on,
the picture may be poor. Turn off one or more
devices.
Good sound but poor color. • Adjust the contrast, color, and brightness
settings. See “Adjusting the TV picture” on
page24.
Audio noise. • Other devices (for example, a surround sound
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV. Try turning off
one device at a time to determine which device
is causing interference. After you have
determined which device is causing
interference, move it further from the TV to
eliminate the interference.
No output from one of the
speakers. • Adjust the audio balance. See “Adjusting sound
settings” on page26.
• Make sure that the audio cables are connected
correctly and securely to your TV.
After images appear. • Do not display a still image, such as a logo,
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen. This
type of damage is not covered by your warranty.
Problem Solution
Problem Solution
Remote control does not
work. • Make sure that the power cord is correctly
connected to your TV and a power outlet.
• Make sure that there are no obstructions
between the remote control and the remote
control sensor on the front of the TV.
• Point the remote co ntrol direc tly at th e remote
control sensor on your TV. For the location of the
remote control sen sor, see “Aiming the remote
control” on page20.
• The supplied batteries are wrapped tightly in
clear plastic. Make sure that you have removed
this plastic from the batteries.
• Make sure that the batteries are installed
correctly. See “Installing remote control
batteries” on page20.
• Replace dead batteries with new batteries. See
“Installing remote control batteries” on page20.
Trouble programming your
existing universal remote
control.
• See instructions and a table of common codes in
“Programming a different universal rem ote
control” on page50.
• Codes are subject to change. For up-to-date
codes, go to
www.insigniaproducts.com/remotecodes
• Replace dead batteries with new batteries. See
“Installing remote control batteries” on page20.
• Refer to the User Guide that accompanied your
universal remote control and contact the
manufacturer if problems persist.
Problem Solution
No power. • Make sure that the power cord is correctly connected to
your TV and a power outlet.
• Unplug the power cord, wait 60 seconds, then plug the
cord back in and turn on your TV.
• Other devices (for example, a surround sound receiver,
external speakers, fans, or hair dryers) may be
interfering with your TV. Try turning off one device at a
time to determine which device is causing interference.
After you have determined which device is causing
interference, move it further from the TV to eliminate
the interference.
“No signal” error
message is displayed. •Press INPUT and make sure that you have selected the
correct input for the device or service you are trying to
use.
• If you are using a cable or satellite box, use the remote
that came with that box to change channels.
• Make sure that you have the correct input selected to
view channels from the cable or satellite box.
After Auto Channel
Search, there are no
channels.
• Reception can vary by channel depending on the
broadcast power level of a given station. Contact your
cable or satellite TV provider.
• Make sure the antenna or c able/satellite TV is
connected securely to your TV.
• Try replacing the cable between the antenna/cable or
cable/satellite box and your TV.