APPENDIX E:

500/5 Specifications

GENERAL SPECIFICATIONS: Recommended Fuse Value: 50A Recommended Fuse Type: AGU or MaxiFuse™

INPUT SECTIONS:

No. of Inputs: Three Stereo Pairs (Front, Rear, Subwoofer)

Input Type: Differential-balanced with RCA jack inputs

Input Range: Switchable from 200mV - 2V RMS to 800mV - 8V RMS

FRONT CHANNELS:

Amplifier Topology: Class AB with patented Absolute Symmetry™ dual N-Channel MOSFET output design Power Supply: Independent, pulse width modulation- regulated switching power supply with multistage impedance optimizing circuitry.

Rated Power (Stereo):

100W RMS x 2 @ 1.5 - 4Ω (11V - 14.5V) Rated Power (Bridged):

200W RMS x 1 @ 3 - 8Ω (11V - 14.5V)

THD at Rated Power: <0.03% @ 4Ω per channel (20 Hz-20 kHz)

Signal to Noise Ratio: >108.5 dB referred to rated power (A-weighted, 20 Hz-20 kHz noise bandwidth)

Frequency Response: 5 Hz - 30 kHz (+0, -1dB)

Damping Factor: >200 @ 4Ω per ch. / 50 Hz, >100 @ 2Ω per ch. / 50 Hz

Slew Rate: ± 25V/µs

Front Filter: State-variable, 12 dB/octave Butterworth or 24 dB/octave Linkwitz-Riley High-Pass with continuously variable cutoff frequency from 50 - 500 Hz, switchable to a range of 500 - 5000 Hz, via x10 switch.

Can also be cascaded from rear filter’s cutoff frequency to operate as a bandpass filter for tri-amp configurations. Defeatable.

REAR CHANNELS:

Amplifier Topology: Class AB with patented Absolute Symmetry™ dual N-Channel MOSFET output design Power Supply: Independent, pulse width modulation- regulated switching power supply.

Rated Power (Stereo):

25W RMS x 2 @ 3 - 4Ω (11V - 14.5V) Rated Power (Bridged):

50W RMS x 1 @ 6 - 8Ω (11V - 14.5V)

THD at Rated Power: <0.03% @ 4Ω per channel (20 Hz - 20 kHz)

Signal to Noise Ratio: >108.5 dB referred to rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) Frequency Response: 5 Hz - 30 kHz (+0, -1 dB)

Damping Factor: >200 @ 4Ω per ch. / 50 Hz, >100 @ 2Ω per ch. / 50 Hz

Slew Rate: ± 25V/µs

Rear Filter: State-variable, 12 dB/octave Butterworth or

24 dB / octave Linkwitz-Riley high-pass with continuously variable cutoff frequency from 50 - 500 Hz, switchable to a range of 500 - 5000 Hz, via x10 switch. Also provides low- pass cutoff for front filter when bandpass mode is used.

SUBWOOFER CHANNEL:

Amplifier Topology: H-Bridge, Class D Mono with impedance optimization and patented discrete drive circuitry

Power Supply: Independent, pulse width modulation- regulated switching power supply

Rated Power: 250W RMS x 1 @ 1.5 - 4Ω (11V - 14.5V)

THD at Rated Power: <0.05% @ 4Ω (50 Hz)

Signal to Noise Ratio: >95 dB referred to rated power (A- weighted, 20 Hz - 20 kHz noise bandwidth)

Frequency Response: 5 Hz - 300 Hz (+0, -1 dB), 5 Hz - 500 Hz (+0, -3 dB)

Damping Factor: >500 @ 4Ω / 50 Hz, >250 @ 2Ω / 50 Hz

Subwoofer Channel Filter: State-variable, 12 dB/octave Butterworth or 24 dB / octave Linkwitz-Riley low-pass with continuously variable cutoff frequency from 40 - 200 Hz. Defeatable.

LF Boost: Single-band, fixed-frequency (48 Hz), fixed “Q” boost, variable from 0 to +15 dB. Defeatable. Port for optional remote bass control to control variable boost from front of vehicle.

Infrasonic Filter: 24 dB/octave @ 30 Hz. Defeatable.

PREAMP OUTPUT:

Tracking type low-pass linked to subwoofer channel filter. Filtering is defeatable to pass a full-range signal from the front channel inputs or a summed signal from the front and rear channel inputs.

DIMENSIONS (LxWxH):

19.7" x 9.25" x 2.36" (500mm x 235mm x 60mm)

Due to ongoing product development, all specifications are subject to change without notice.

28

JL AUDIO 500/5

JL AUDIO 500/5

29