JVC CA-UXF4VB, LVT2123-029A, SP-UXF4VB, UX-F4VB manual

ENGLISH (1/2)LVT2123-029A[US/UX/UG/UW]

Specifications

Getting started

Main unit—CA-UXF4VB		General
Output Power:	100 W (50 W + 50 W) at 6 Ω (10% THD)	Power source:	AC 110 V– 127 V/AC 220 V– 240 V
Audio Input:	AUDIO IN: Stereo mini (ø 3.5 mm)	(adjustable with the voltage selector), 50 Hz/60 Hz

❍Supplied accessoriesAfter unpacking, check to make sure that you have all

❍Prepare the remote control

When you use the remote control for the first time, pull out the insulation sheet.

MICRO COMPONENT SYSTEM

UX-F4VB	INSTRUCTIONS
—consists of CA-UXF4VB and SP-UXF4VB

SUPER VIDEO

Thank you for purchasing a JVC product.

	For turning off the demonstration display, see	0510YOMMDWCDT
	“Canceling the display demonstration” in “Initial	0510YOMMDWCDT
	“Canceling the display demonstration” in “Initial
	settings.”	©2010 Victor Company of Japan, Limited
		©2010 Victor Company of Japan, Limited

Microphone Input:	MIC: Monaural mini (ø 3.5 mm)				Power consumption (at operation):		45 W
Audio output: SUBWOOFER OUT:		500 mV/10 kΩ			Power consumption (on standby):		1.00 W or less
Digital output: OPTICAL DIGITAL OUT:					Dimensions (approx.) (W × H × D) (including projecting
	–21 dBm to –15 dBm (660 nm ±30 nm)				parts):	236 mm × 123 mm × 285 mm
VIDEO OUT × 1					Mass (approx.):		2.0 kg
COMPONENT VIDEO OUT × 1					Speaker—SP-UXF4VB
Speaker impedance:			6 Ω – 16 Ω		Speaker—SP-UXF4VB
Speaker impedance:			6 Ω – 16 Ω		Speaker type: Bass-reflex type (Magnetically-shielded type)
Tuner
Tuner					Tweeter:		4 cm
FM frequency:		87.50 MHz – 108.00 MHz			Woofer:		12 cm
AM frequency					Impedance:		6 Ω
For Saudi Arabia:		531 kHz – 1 602 kHz			Dimensions (approx.) (W × H × D) (including projecting
		(at 9 kHz intervals)			parts):	141 mm × 250 mm × 181 mm
		530 kHz – 1 600 kHz			Mass (approx.):		2.2 kg each
		(at 10 kHz intervals)			Supplied accessories
For other countries/areas:		531 kHz – 1 710 kHz			Supplied accessories
For other countries/areas:		531 kHz – 1 710 kHz			See “Supplied accessories” in “Getting started.”
		(at 9 kHz intervals)			See “Supplied accessories” in “Getting started.”
		(at 9 kHz intervals)
		530 kHz – 1 710 kHz
		(at 10 kHz intervals)			Design and specifications are subject to change without
USB					Design and specifications are subject to change without
USB					notice.
USB specification:	Compatible with USB 2.0 Full Speed
Compatible device:		Mass storage class
Compatible system:		FAT16, FAT32
Output power:		DC 5 V		500 mA
Output power:		DC 5 V		500 mA
SD
Compatible device:			SD, SDHC
Compatible system:		FAT16, FAT32

the following items:•Remote control (× 1)•Lithium coin battery CR2025 (× 1)

–The battery has been installed in the remote control when shipped from the factory.

•FM antenna (× 1)•AM loop antenna (× 1)•Composite video cord (× 1)•AC plug adaptor (× 1)(not supplied for Middle Eastern and Saudi Arabian models)If anything is missing, consult your dealer immediately.In this manual...

•The remote control buttons are used for explaining the operations unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations.

•The English on-screen displays and terms are used for explanation though you can change the on-screen language.

•“SD card” refers to both SD card and SDHC card.•“File” and “track” are used interchangeably.

To replace the battery in the remote controlLithium coin battery (product number: CR2025)

NOTES:

•Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.

•To prevent the battery from overheating, cracking, or starting a fire:

–Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.

–Do not leave the battery with other metallic materials.–Wrap the battery with tape and insulate when throwing away or saving it.–Do not poke the battery with tweezers or similar tools.

•Dispose of battery in the proper manner, according to federal, state, and local regulations.

•The battery (battery pack or battery installed) shall not be exposed to excessive heat source such as sunshine, fire or the like.

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

Connections Do not connect the AC power cord until all other connections have been made.

1.Front: No obstructions and open spacing.

2.Sides/Top/Back: No obstructions should be placed in the areas indicated by the dimensions in the illustration.

3.Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Front view

Side view

SpeakerSpeaker

Main unit

Main unit

After connecting a TV, select the appropriate video signal output setting according to the connection method. See “Setting the scanning mode” in “Initial settings” below.

NOTES:

•Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord. Also, keep the antennas away from metallic parts of the System, connecting cords, and the AC power cord. Otherwise, it could cause poor reception.

•When connecting the speaker cords, match the polarities of the speaker terminals: red to (+) and black to (–).

•DO NOT connect more than one speaker to each terminal.

•Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the System.

•DO NOT allow the conductor of the speaker cords to come into contact with the metallic parts of the System.

•The speakers are magnetically shielded to avoid color distortions on TVs. However, if not installed properly, it may cause color distortions. Therefore, pay attention to the following when installing the speakers.

–When placing the speakers near a TV set, turn off the TV’s main power switch or unplug it before installing the speakers. Then wait at least 30 minutes before turning on the TV’s main power switch again.

–Some TVs may still be affected even though you have followed the above instructions. If this happens, move the speakers away from the TV.

•Connect your TV directly to the System. Connecting the System to a TV via a VCR or an HDD DVD recorder may interfere with your viewing. Connecting an integrated TV/VCR system to the System may also interfere with your viewing.

FM antenna (supplied): Extend it so that you can obtain the best reception.	Before connecting the
	System to the power supply,
For better FM reception	make sure that the powered
For better FM reception	subwoofer is turned off.	OPTICAL	OPTICAL	Optical digital cord
Disconnect the supplied FM antenna, and connect to an outdoor FM antenna	subwoofer is turned off.	OPTICAL	OPTICAL	Optical digital cord
	From the powered	DIGITAL	DIGITAL	(not supplied)
(not supplied) using a 75 Ω wire with coaxial type connector.	subwoofer	OUT	OUT	(not supplied)
		OUT	OUT

	(not supplied)

Precautions

Maintenance

Playable disc/file types

• When playing multi-channel encoded software,

the System properly converts the multi-channel

Notes on the power cord

•When you go away for an extended period of time, remove the plug from the wall outlet.

•When unplugging the System from the wall outlet, always pull the plug, not the power cord.

•Do not handle the power cord with wet hands.•Disconnect the power cord before cleaning the System or moving the System.

•Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.

Avoid moisture, water, dust, and high temperatures•Do not place the System in moist or dusty places.

•If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using the System in this state may cause a fire or electrical shock.

•Do not expose the System to direct sunlight or place it near a heating device.Notes on installation

•Select a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.

•Do not install the System in a place subject to vibrations.•Do not put heavy objects on the System.To prevent malfunction or damage to the System

•Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.

•Do not block the vents.

There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.

To get the best performance of the System, keep your discs and the mechanism clean.

Handling discs

•Remove the disc from its case by holding it at the edge while pressing the center hole lightly.

•Do not touch the shiny surface of the disc, or bend the disc.•Put the disc back in its case after use.

•Be careful not to scratch the surface of the disc when placing it back in its case.

•Avoid exposure to direct sunlight, temperature extremes, and moisture.To clean the disc:Wipe the disc with a soft cloth in a straight line from center to edge.Cleaning the System

•Stains should be wiped off with a soft cloth. If the System is heavily stained, wipe it with a cloth soaked in water- diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

•Since the System may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following:

–DO NOT wipe it hard.–DO NOT wipe it with thinner or benzine.–DO NOT apply any volatile substances such as insecticides to it.–DO NOT allow any rubber or plastic to remain in contact for a long time.

DIGITAL VIDEO

COMPACT

SUPER VIDEO

DIGITAL AUDIO

CD-R/-RW: Recorded in the Audio CD, Video CD, and SVCD formats. MP3, WMA, JPEG, MPEG-1, MPEG-2, and DivX*1 files written in accordance with the “ISO 9660” format can also be played.

DVD-R/-RW, +R/+RW: Recorded in the DVD Video format. MP3, WMA, JPEG, MPEG-1, MPEG-2, and DivX*1 files written in the UDF-Bridge format can also be played.

DVD-R/-RW: Recorded in the DVD Video Recording (VR) format.

USB mass storage class device, SD/SDHC card: MP3, WMA, JPEG, MPEG-1, MPEG-2, and DivX*1 files.

In addition to the above discs/files, this System can play back audio data recorded on CD-Extra.

• The following discs cannot be played back: DVD-RAM,

CD-I (CD-I Ready) and Photo CD. Playing back these discs

will generate noise and damage the speakers.

• It is possible to play back finalized +R/+RW (DVD Video

format only) discs. The DVD indicator lights up when a

+R/+RW disc is loaded.

•For MP3/WMA playback...–Some MP3/WMA files may not be played back due to their recording conditions.–This System can play only a disc of ISO 9660 Level 1 or Level 2.

–It is recommended to record each file at a sampling rate of 44.1 kHz and at a data transfer rate of 128 kbps.

–This System cannot play back files made at a bit rate of less than 64 kbps.–This System can show the Tag data (Version 1).•For playback of files on a USB mass storage class device/ SD card...–You cannot play back files larger than 2 GB.

–This System may not play back some USB mass storage class devices/SD cards and does not support DRM (Digital Rights Management).

•This System can play back files on DVD, CD*2, USB mass storage class device*2 and SD/SDHC card*2 recorded by JVC EVERIO camcorders with the extension <.mod>. These files cannot be played back if HD format is used.

*2 Only when the maximum bit rate is less than 2 Mbps.About color system•Connect a PAL or NTSC TV to this System.•This System can play back discs recorded in PAL and NTSC video format.Note on Region Code

DVD players and DVDs have their own Region Codes. This System can play back only DVDs with an appropriate Region Code.

Country/area	Region Code
Middle East and Saudi Arabia	2

From			From
right	Black	Black	left
speaker			speaker
	Red	Red

Black

White	AM loop antenna
	(supplied)

Turn it until the best reception is obtained.NOTE:

Keep the AM loop antenna cable wrapped around the AM loop antenna frame, otherwise the effectiveness and sensitivity of the AM loop antenna may be reduced.

When you connect a TV using a component video cord, you can enjoy a high quality picture by selecting the progressive scanning mode. To select the scanning mode, see “Setting the scanning mode” in “Initial settings” below.

Connect your TV to the System using either a composite video cord or component video cord.

	Y
	PB
	PR
		Green
		Blue
	Yellow	Component video
	Yellow	cord (not supplied)
	Composite video cord	cord (not supplied)
	Composite video cord	Red
	(supplied)	Red

Voltage selector switch(on the bottom of the System)

signals into 2 channels, and emits the downmixed

sound from the speakers. To enjoy the powerful

sound of the multi-channel encoded software,

connect a proper decoder or an amplifier with

a built-in decoder to the OPTICAL DIGITAL OUT

terminal.

• Set “AUDIO OUT” in the “ ” menu correctly

according to the connected digital audio

equipment (see “Setup menu operations of the

System” on page 4).

• The digital signal is transmitted through the

OPTICAL DIGITAL OUT terminal when “DVD/CD,”

“USB,” or “SD” is selected as the source.

To a wall outlet

• If a wall outlet does not match the AC plug, use the supplied AC plug adaptor (not supplied for Middle Eastern and Saudi Arabian models).

CAUTION for mains (AC) line

BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk of fire/electric shock.

• “DVD Logo” is a trademark of DVD Format/Logo Licensing

Corporation.

• The System recognizes up to 999 tracks (files) and 130

groups.

*1 Maximum resolution:720 × 480@30fps / 720 × 576@25fps

Southeast Asia	3
Central and South America	4

Ex.: For Southeast Asia•“RG ERROR” appears if a DVD with an incompatible Region Code is loaded.Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of the Non-DVD side of a DualDisc in this product may not be recommended.

Initial settings

Canceling the display demonstration

When you plug in and turn on the System, the display demonstration starts automatically if no operation is done for about 2 minutes.

To cancel the display demonstration(On the main unit)(Hold)

Setting the clock

•If you have already set the clock before, press CLOCK repeatedly until the clock setting mode is selected.

2Adjust the hour and minute.•To go back to the previous step, press CANCEL while holding SHIFT.

•The clock may gain or lose 1 to 2 minutes per month. You may need to readjust the clock periodically.

Setting the scanning modeSelect the video signal output setting according to the type of your TV.

•You can set the scanning mode only when “DVD/CD,” “USB,” or “SD” is selected as the source.

						On the TV screen
						On the TV screen
						INTERLACE-YUV
(While holding...)						P-SCAN YPBPR
						INTERLACE-YUV

•Select “INTERLACE-YUV” when you have connected your TV to the System using a composite video cord.

		For a progressive TV.
		Select to enjoy a progressively
	P-SCAN YPBPR	scanned picture through the
	P-SCAN YPBPR	COMPONENT VIDEO OUT jacks.
		• PRGR. (Progressive) indicator lights
		up.
	INTERLACE-	For a conventional TV.
	INTERLACE-	Select when connecting the TV through
	YUV	Select when connecting the TV through
	YUV	the VIDEO OUT jack.
		the VIDEO OUT jack.