ENGLISH
Warnings, Cautions and Others / Mises en garde, précautions et indications diverses
USA ONLY
HOME THEATER SOUND SYSTEM
TH-BC3
Thank you for purchasing a JVC product. Before operation, please read the instructions carefully.
For customer use:Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No.Serial No.INSTRUCTIONS
EN © 2010 Victor Company of Japan, LimitedThe lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Pour lesLe symbole de l’éclair à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’une “tension dangereuse” non isolée dans le boîtier du produit. Cette tension est suffisante pour provoquer l’électrocution de personnes.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’opérations d’entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d’instructions.
CAUTIONThe
button in any position does not disconnect the mains line.Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
•When the System is on standby, the STANDBY lamp lights red.
•When the System is turned on, the STANDBY lamp goes off. The power can be remote controlled.
ATTENTIONLa touche 
, dans n’importe quelle position, ne déconnecte pas le système du secteur. Déconnectez la fiche de secteur pour mettre l’appareil complètement hors tension (le témoin STANDBY s’éteint). La fiche secteur ou un coupleur est utilisé comme dispositif de déconnexion de l’appareil, et l’appareil déconnecté doit être prêt à être utilisé.
CAUTION
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
ATTENTION
Les piles ne doivent en aucun cas être exposées à une chaleur excessive (lumière du soleil, feu, etc.).
CAUTION
To reduce the risk of electrical shocks, fire, etc.:1.Do not remove screws, covers or cabinet.2.Do not expose this appliance to rain or moisture.ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:1.Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2.Ne pas exposer l’appareil à la pluie ni à l’humidité.This device compiles with
(2)this device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme au réglement
(1)il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
For CanadaTHIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR; “APPAREILS NUMERIQUES”,
For U.S.A.
WARNINGTO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
Pour les
POUR PRÉVENIR LES RISQUES D’INCENDIE OU DE CHOCS ÉLECTRIQUES, NE PAS EXPOSER CE APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
CAUTION
•Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
•Do not place any naked flame sources, such as lighted candles, on the apparatus.
•When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.
•Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
ATTENTION
•Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les trous de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut ne pas être évacuée correctement de l’appareil.)
•Ne placez aucune source de flamme nue, telle qu’une bougie, sur l’appareil.•Lors de la mise au rebut des piles, veuillez prendre en considération les problèmes de l’environnement et suivre strictement les règles et les lois locales sur la mise au rebut des piles.
•N’exposez pas cet appareil à la pluie, à l’humidité, à un égouttement ou à des éclaboussures et ne placez pas des objets remplis de liquide, tels qu’un vase, sur l’appareil.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and(2)this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by
the manufacturer for compliance could void the user’s authority to operate the equipment.
Cet appareil est conforme à la partie 15 des règles de la FCC (Federal Communications Commission). Le fonctionnement est sujet aux deux conditions suivantes:
(1)Cet appareil ne peut pas causer d’interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris des interférences qui peuvent causer un mauvais fonctionnement.
Tout changement ou modification non expressément approuvés par le fabricant pour conformité peut annuler l’autorité de l’utilisateur d’utiliser l’appareil.
[European Union only][Union européenne seulement]To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
| 1. Front: No obstructions and open spacing. |
Playable iPod models
• Compatible iPod:| • “Made for iPod” and “Made for iPhone” mean that an |
| electronic accessory has been designed to connect |
| specifically to iPod or iPhone, respectively, and |
Introduction
Specifications
Troubleshooting
2. | Sides/Top/Back: No obstructions should be placed in the areas indicated by the dimensions in the illustration. |
3. | Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 |
| cm |
Pour éviter tout risque de choc électrique et d’incendie, placez l’appareil en respectant ce qui suit:
1.Avant: Rien ne doit gêner le dégagement.2.Flancs/Dessus/Arrière: Aucun obstacle ne doit être placé dans les zones indiquées par les dimensions dans l’illustration.
3.Dessous: Poser l’appareil sur une surface plate. Laissez suffisamment d’espace pour que la ventilation puisse s’effectuer correctement en plaçant l’appareil sur un socle d’une hauteur de 10 cm ou plus.
Front / Face
15 cm | 15 cm | 15 cm |
10 cm For U.S.A.
Caution: Changes or modifications not expressly approved by party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.–Increase the separation between the equipment and receiver.–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.Pour les
Attention: Les changements ou les modifications qui ne sont pas explicitement approuvés par la partie responsable de l’observance pourraient mettre fin au droit de l’utilisateur d’utiliser le matériel.
Remarque: Cet appareil a été testé et il s’est avéré conforme aux limites applicables à un appareil numérique de classe B, en vertu de la Partie 15 des Règles de la FCC. Ces limites sont conçues de manière à assurer une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet appareil produit, utilise et peut émettre une énergie de haute fréquence et, s’il n’est pas installé et utilisé en conformité avec les instructions, il peut causer des interférences nuisibles aux communications radio. Il n’y a, toutefois, aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si cet appareil cause effectivement des interférences nuisibles
àla réception de la radio ou de la télévision, ce qu’on peut établir en mettant l’appareil en marche et à l’arrêt, nous encourageons l’utilisateur à tenter de corriger l’interférence par une ou plusieurs des mesures suivantes:
– réorienter ou déplacer l’antenne de réception;– accroître la séparation entre l’appareil et le récepteur;– brancher l’appareil dans une prise ou un circuit autre que celui auquel le récepteur est branché;
– consulter un vendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide.
| Made for | Audio | Video |
| iPod nano (6th generation) |
| * |
| iPod nano (5th generation) |
|
|
| iPod nano (4th generation) |
|
|
| iPod nano (3rd generation) |
|
|
| iPod nano (2nd generation) |
| – |
•If the NOT SUPP indicator is shown on the display, the connected iPod is not supported.
•If iPod does not play correctly, update iPod software to the latest version.–For details about updating iPod, check on the Apple web site <http://www.apple.com/>.
| has been certified by the developer to meet Apple |
| performance standards. Apple is not responsible for |
| the operation of this device or its compliance with |
| safety and regulatory standards. Please note that the |
| use of this accessory with iPod or iPhone may affect |
| wireless performance. |
| • iPhone, iPod, iPod classic, iPod nano and iPod touch |
| are trademarks of Apple Inc., registered in the U.S. |
| and other countries. |
| • HDMI, the HDMI logo and |
| Interface are trademarks or registered trademarks of |
| HDMI Licensing LLC. |
| • HDCP is the abbreviation of |
| Content Protection,” and is the |
| control technology licensed by Digital Content |
| Protection, LLC. |
| • In this manual, “iPod” means iPod, iPod touch and |
| iPhone device. When iPod touch or iPhone device |
| is especially referred to, “iPod touch” or “iPhone” is |
| used. |
When no operation is done in certain situations for 29 minutes, the unit turns off automatically. This function is on at the initial setting. For details, refer to “Operations.”
In this manual, the remote control buttons are used for explaining the operations unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations.
Notes on handling
Important cautionsInstallation of the System•Select a place which is level, dry, and neither too hot nor too cold; between 5°C and 35°C (41°F and 95°F).
•Leave sufficient distance between the System and the TV.•Do not use the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or vibration.
•Install the System in a location with adequate ventilation to prevent internal heat buildup.
Power cord•Do not handle the power cord with wet hands.•A small amount of power is always consumed while the power cord is connected to the wall outlet.
•Do not pull on the cord to unplug the power cord. When unplugging the power cord, always grasp and pull the plug so as not to damage the cord.
To prevent malfunctions of the System•There are no
Do not expose the System to direct sunlight and do not place it near any heating devices.
When you are awayWhen away on holiday or for other reasons for an extended period of time, disconnect the power cord from the wall outlet.
•Stains on the System should be wiped off with a soft cloth. If the System is heavily stained, wipe it with a cloth soaked in water diluted neutral detergent and wrung well, then wipe clean with a dry cloth.
•Since the System may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following:
–DO NOT wipe it forcefully.–DO NOT wipe it with thinners, benzines or other organic solvents including disinfectants.
–DO NOT apply any volatile substances such as insecticides to it.–DO NOT allow any rubber or plastic to remain in contact with it for a long time.
•Do not place anything on top of the System. Doing so may cause the System to fall, causing malfunctioning and/or injury.
•The manufacturer accepts absolutely no liability for any accidents or damage resulting from inadequate assembly or mounting, insufficient strength of attachment, misuse or abuse, or natural disasters.
If water gets inside the SystemTurn the System off and disconnect the power cord from the wall outlet, then call the store where you purchased this System. Using the System in this condition may cause a fire or electrical shock.
Supplied accessories
Check to make sure you have all of the supplied accessories. If anything is missing, contact your dealer immediately.
•Remote control–The battery has been installed in the remote control when shipped from the factory.
•Core filter (× 2)•TV remote pass through cable (× 1)•| Output power | 60 W (30 W per channel- | |||||||
| measure at 1 kHz Optical | |||||||
| Digital In at full scale | |||||||
| sinewave), RMS at 4 Ω at 1 | |||||||
| kHz, with 10% total harmonic | |||||||
| distortion | |||||||
| Audio section |
|
|
|
|
|
|
|
|
| Analog Input | ANALOG: 1 Vrms/50 kΩ | |||||||
| Digital Input* | DIGITAL 1 (OPTICAL) : | |||||||
| ||||||||
| ±30 nm) |
|
|
|
| |||
| DIGITAL 2 (COAXIAL) : | |||||||
| Speaker section | 0.5 | |||||||
|
|
|
|
|
|
|
| |
| Type: | ||||||||
| Speaker: | Woofer: 8 cm | |||||||
| Tweeter: 2.5 cm (1”) balance | |||||||
| dome × 2 |
|
|
|
| |||
| Power Handling Capacity: | 30 W |
|
|
|
| |||
| Impedance: | 4 Ω |
|
|
|
| |||
| Frequency Range: | 82 Hz to 25 kHz | |||||||
| Sound Pressure Level: | 88 dB/W•m | |||||||
| General |
|
|
|
|
|
|
|
|
| Power Source (DC IN): | DC 19 V |
|
|
| 3.37 A | |||
|
|
| ||||||
| AC adaptor | Input: AC 100 – 240 V , | |||||||
| 50 Hz/60 Hz, 1.5 A – 0.9 A | |||||||
| Output: DC19 V |
| 3.37 A | |||||
|
| |||||||
| Power Consumption(in Standby mode): | ||||||||
| 0.50 W or less | |||||||
| Dimensions (W × H × D): | 900 mm ×98 mm × 107 mm | |||||||
| ||||||||
| Mass: | 3.4 kg (7.4 lbs) | |||||||
| Tuner |
|
|
|
|
|
|
|
|
| FM tuning range: | 87.5 MHz – 108.0 MHz | |||||||
| iPod |
|
|
|
|
|
|
|
|
| Output power: | DC 5 V |
|
| 1 A | ||||
| ||||||||
| HDMI |
|
|
|
|
|
|
|
|
| HDMI Input: | HDMI 1 IN, HDMI 2 IN* | |||||||
| HDMI Output: | HDMI OUT | |||||||
| Max. Capability: | 1920 × 1080 at 60 Hz | |||||||
Output power: | DC 5 V |
|
| 55 mA | ||||
| ||||||||
If you have a problem with this System, check this list for a possible solution before calling for service.
POWERPower does not come on.=The power cord is not inserted securely. Plug it in securely.The unit turns off suddenly.=Auto power save function is on. Refer to “Activating/ deactivating APS (Auto Power Save)” in “Basic operation.”
REMOTE CONTROLThe remote control does not work.=Pull out the insulation sheet.=Sunlight is shining directly on the remote sensor. Hide the remote sensor from direct sunlight.
=The path between the remote control and the remote sensor on the front panel is blocked.
=Point the remote control at the remote sensor on the front panel.=Signals cannot reach the remote sensor. Move closer to the unit.=The battery is exhausted. Replace the battery.The remote control of the TV does not work.=If you install the unit near the TV, connect the TV remote pass through cable (supplied).
FM tunerHard to listen to broadcasts because of noise.=Electrostatic discharge from your body may cause noise. If this happens, turn off and on the unit again.
External componentsNo sound can be heard when DIGITAL 1 or DIGITAL 2 is selected as a source.=Check the output setting of the connected digital components. Set the output setting as the PCM signal is outputted.
iPodiPod cannot be connected firmly.=Check to see whether the connector between iPod and the unit is not damaged, and connect it.
iPod does not provide sound.=iPod is not properly connected. Remove iPod from the unit, and then connect it again.
iPod cannot be charged.=iPod is not properly connected. Remove iPod from the unit, and then connect it again. After connecting iPod, turn on the power again.
HDMINo sound can be heard when HDMI 1 or HDMI 2 source is selected as a source.=Check the output settings on the HDMI connected devices. Set the audio output setting to PCM signal and enable HDMI Audio Out.
No sound can be heard when TV ARC is selected as a source.=Check if your TV supports this function and turn on the settings for ARC and set the digital audio output setting to PCM signal on your TV.