Internet Explorer Setting

Settings (continued)

Encoding Page (continued)

 

 

 

 

 

 

 

 

 

 

 

 

C Multi-Encode2 (continued)

 

 

 

 

 

 

 

 

 

 

 

Encoder

Encoding

 

Displays the "MPEG4" encoding selected for Multi-Encode2.

 

 

No.2

Display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Framesize

 

Displays the frame size selected for Multi-Encode2.

 

 

 

 

 

 

 

 

 

Framerate

 

Specify the frame rate for Multi-Encode2.

 

 

 

 

 

[Set values: 15 fps, 10 fps, 7.5 fps, 1 fps]

 

 

 

 

 

 

 

 

 

Bitrate

 

Select whether to set the control rate mode for encoding to CBR

 

 

 

 

 

(Constant Bit Rate) or VBR (Variable Bit Rate).

 

 

 

 

 

CBR

: Data is encoded at a fixed bit rate regardless of the condition of

 

 

 

 

 

 

 

input video signals. It is easy to estimate the bit rate. Select

 

 

 

 

 

 

 

from the list of bit rate ranges.

 

 

 

 

 

VBR

: The bit rate varies according to the condition of input video

 

 

 

 

 

 

 

signals. The picture quality is stabled but it is difficult to

 

 

 

 

 

 

 

estimate the bit rate. Select from the list of bit rate ranges.

 

 

 

 

 

[Set values: CBR, VBR]

 

 

 

 

 

Bit rate range

 

 

 

 

 

[Set values: 64, 128, 256, 384, 512, 768, 1024, 1536, 2048, 3072, 3584,

 

 

 

 

 

 

 

4096, 8192] kbps

 

 

 

 

 

 

 

 

 

I Frame

 

Select the I-frame interval. Encoding starts from the I-frame. Shortening

 

 

 

Interval

 

the interval stabilizes the picture quality even when there are rapid

 

 

 

 

 

changes in the video image; however, the picture quality for images with

 

 

 

 

 

little change will deteriorate. In addition, when multicast packet loss

 

 

 

 

 

occurs, the time interval required to restore the image is shorter.

 

 

 

 

 

[Set values: 15, 30] Frame

 

 

 

 

 

 

 

D Monitor Output

 

Sets monitor output.

 

 

 

 

 

[Set values: ON, OFF]

 

 

 

 

 

Memo:

 

 

 

 

 

 

 

 

 

 

 

 

● To turn the monitor output ON, set the following in the [Single-Encode]

 

 

 

 

 

(JPEG/H.264 Baseline/H.264 High) option:

 

 

 

 

 

• Aspect ratio = 16:9

 

 

 

 

 

• Frame size = 1920 x 1080

 

 

 

 

 

• Frame rate = 5 fps or less

 

 

 

 

 

● If you changed the setting of the camera’s monitor selection switch,

 

 

 

 

 

you need to restart the camera.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* The [Set values] in bold letters are factory defaults.

 

32