Kenwood DVF-3070

Knowledge

DVF-3070 (EN/E,T,X,Y)

÷Load a disc and press the 6 key.

÷Turn the disc over and properly place it on

the disc tray.

÷Turn on the TV.

÷Properly reconnect the connection cords.

÷This is not a malfunction.

÷Properly connect the audio cords.

÷Set the sound volume to an appropriate

level.

÷Press the 6 key to resume normal play-

back mode.

÷Separate this unit as far as possible from

the device you think is generating the

noise.

÷Refer to the "Disc handling precautions"

section and wipe dirt from the disc. 9

÷Use a new disc.

Refer to the "Caution on condensation" sec-

tion and evaporate the condensation.

÷Approximately 10 to 20 seconds are re-

quired for a disc to start playing, although

the time differs depending on the disc.

÷Properly place the disc on the tray.

÷Refer to the "Video formats" section ,and

use a disc with the appropriate video for-

mat for your TV or a TV with the appropriate

video format for the disc. 8

÷The subtitle cannot be displayed when the

DVD disc being played does not contain

the recording of subtitles.

÷Press the SUBTITLE ON/OFF key to

switch on the subtitle mode. ª

÷The voice (or subtitle) language cannot be

changed when the DVD disc being played

does not contain the recording of more

than one voice (or subtitle) language.

÷The viewing angle cannot be changed

when the DVD disc being played does not

contain the recording of more than one

angle.

÷More than one viewing angle may be re-

corded only in limited sections in a disc.

In case of difficulty

Operation to reset

What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the

table below to see if the problem can be corrected before seeking help from your dealer or service representative.

÷There is no disc in the player.

÷There are no signals recorded on the side of

the disc being played.

÷The TV is not turned on.

÷The connection cords are not properly con-

nected.

÷The picture is slightly disrupted during fast

forward and fast reverse operations.

÷The audio output cords are not properly con-

nected.

÷The volume control of the TV or amplifier is

not adjusted properly.

÷The player is in a special playback mode.

÷A nearby device is generating noise.

÷The disc is dirty.

÷The disc is damaged.

÷There is condensation on the optical lens.

÷Time is required for the unit to detect the

disc type and size and for the rotation of the

motor to stabilize. This is not a malfunction.

÷The disc is not placed horizontally.

÷The video format of the disc being played

does not match that of the connected TV

monitor.

÷The DVD disc being played does not contain

the recording of subtitles.

÷The subtitle mode is set to off.

÷The DVD disc being played does not contain

the recording of more than one audio (or sub-

title) language.

÷The DVD disc being played does not contain

the recording of more than one angle.

÷You are attempting to switch the angle in a

DVD section where more than one angle is

not recorded.

RemedyCause

DVD player unit

Symptom

Playback does not start when the 6 key is

pressed.

Playback starts but no image/sound is seen

heard.

The picture is disrupted when the image is

fast forwarded or fast reversed.

No sound is heard.

The picture does not look good or the pic-

ture/sound quality is poor.

It takes a while for the disc to start playing.

The tray opens automatically.

The top and bottom of the screen cannot be

seen, or the screen becomes black-and-

white.

The subtitle is not displayed.

The voice (or subtitle) language cannot be

changed.

The viewing angle cannot be changed.

1Press the MENU key on the remote to enter SETUP

MENU.

2Select the PREFERENCE, then press the ENTER key.

3Select DEFAULTS, press the Cursoe right (3) key to

select RESET.

4Press the numeric keys as shown below.

Press 1, 3, 9, 7, then press the ENTER key.

When resetting is done according to this method, all set-

tings, including the settings for password and parental level,

will be reset to the factory defaults.

The microprocessor may fall into malfunction (impos-

sibility to operate erroneous display, etc.) when the

power cord is unplugged while power is ON or due to

an external factor.

In this case, switch off the power, wait for several sec-

onds, and then switch the power on again.

Return to the factory defaults by resetting the micropro-

cessor is done as shown as follows.

*5357/44-48/EN 03.5.20, 10:33 AM44